- 您现在的位置：买卖IC网 > PDF目录1774 > ADM1041AARQZ-REEL7 (Analog Devices Inc)IC SECONDARY SIDE CTRLR 24QSOP PDF资料下载
参数资料
| 型号： | ADM1041AARQZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/64页 |
| 文件大小： | 0K |
| 描述： | IC SECONDARY SIDE CTRLR 24QSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 1,000 |
| 应用： | 次级侧控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
| 配用： | ADM1041-EVAL-ND - BOARD EVALUATION ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
ADM1041
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
V DD 1
V LS /C S –/FS 2
C S + 3
C CMP 4
V CMP 5
24
23
22
21
20
SHRO
SHRS+
SCMP
V S +
V S –/SHRS–
F D 6
GND 7
ICT 8
ADM1041
TOP VIEW
(Not to Scale)
19 F G
18 V REF /AC_OK/OTP/MON5
17 DC_OK/MON4
PULSE/AC SENSE 1/MON1 9
AC SENSE 2/MON2 10
CBD/ALERT 11
PEN 12
16
15
14
13
PSON/MON3
ADD0
SDA/PS ON LINK
SCL/AC_OKLink
Figure 7. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
Mnemonic
V DD
V LS /C S –/FS
C S +
C CMP
V CMP
FD
GND
ICT
PULSE/AC SENSE 1/MON1
Description
Positive Supply for the ASIC. Normal range is 4.5 V to 5.5 V. Absolute maximum rating is 6.5 V.
Inverting Differential Current Sense Input, Local Voltage Sense Pin, and OrFET Source. These three
functions are served by a common divider. The local voltage sense input is used for local overvoltage
and undervoltage sensing. This pin also provides an input to the false UV clamp that prevents
shutdown during an external load overvoltage condition. When supporting an OrFET circuit, this pin
represents the FET source and is the inverting input of a differential amplifier looking for the presence
of a reverse voltage across the FET, which might indicate a failure mode.
Noninverting Differential Current Sense Input. The differential sensitivity of C S + and C S – is normally
around 10 mV to 40 mV at the input to the ASIC. Nulling any external divider offset is achieved by
injecting a trimmable amount of current into either the inverting or noninverting input of the second
stage of the current sense amplifier. A compensation circuit is used to ensure the amount of current
for zero-offset tracks the common-mode voltage. Nulling of any amplifier offset is done in a similar
manner except that it does not track the common-mode voltage.
Current Error Amplifier Compensation. This pin is the output of the current limit transconductance
error amplifier. A series resistor and a capacitor to ground are required for loop compensation.
Voltage Error Amplifier Compensation. This is the output of a voltage error transconductance
amplifier. Compensate with a series capacitor and resistor to ground. An external emitter-follower or
buffer is typically used to drive an optocoupler. Output voltage positioning may be obtained by
placing a second resistor directly to ground. Refer to Analog Devices applications notes on voltage
positioning.
A divider from the OrFET drain is connected here. A differential amplifier is then used to detect the
presence of a reverse voltage across the FET, which indicates a fault condition and causes the OrFET
gate to be pulled low.
Ground. This pin is double bonded for extra reliability. If the ground pin goes positive with respect to
the remote sense return (V S –) for a sustained period indicating that the negative remote sense line is
disconnected, PEN will be disabled.
Input for Current Transformer. The sensitivity of this pin is suitable for the typical 0.5 V to 1 V signal
that is normally available. If this function is enabled, the C S + amplifier is disabled. This pin is also used
for extended SMBus addressing, i.e., pulled below ground to allow additional SMBus addresses.
Pulse Present, AC/Bulk Sense 1, or Monitor 1 Input.
PULSE: This tells the OrFET circuit that the voltage from the power transformer is normal. A peak hold
allows the OrFET circuit to pass through the pulse skipping that occurs with very light loads but turns
off the circuit about one second after the last pulse is recognized.
AC SENSE 1: This sense function also uses the peak voltage on this pin to measure the bulk capacitor
voltage. If too low, AC_OK and DC_OK can warn of an imminent loss of power. Threshold level and
hysteresis can be trimmed. When not selected, AC SENSE 1 defaults to true.
MON1: When MON1 is selected for this pin, its input is compared against a 1.25 V comparator that
could be used for monitoring a post regulated output; includes overvoltage, undervoltage, and
overtemperature conditions.
Rev. A | Page 14 of 64
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1041AARQZ | IC SECONDARY SIDE CTRLR 24QSOP |
| ADM1060ARU | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1041ARQ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。