- 您现在的位置：买卖IC网 > PDF目录1774 > ADM1041AARQZ-REEL7 (Analog Devices Inc)IC SECONDARY SIDE CTRLR 24QSOP PDF资料下载
参数资料
| 型号： | ADM1041AARQZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/64页 |
| 文件大小： | 0K |
| 描述： | IC SECONDARY SIDE CTRLR 24QSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 1,000 |
| 应用： | 次级侧控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
| 配用： | ADM1041-EVAL-ND - BOARD EVALUATION ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
ADM1041
CURRENT SENSING
Current is typically sensed by a low value resistor in series with
the positive output of the power supply, just before the OrFET
or diode. For high voltages (12 V and higher), this resistor is
usually placed in the negative load. A pair of closely matched
voltage dividers connected to Pins 2 and 3 divide the common-
mode voltage down to approximately 2.0 V. The divider ratio
must be the same as used in the local and remote voltage sense
circuits. Alternatively, current may be sensed by a current
transformer (CT) connected to Pin 8. The ADM1041 must be
configured via the SMBus to select one or the other. See
CURRENT TRANSFORMER INPUT
The ADM1041 can also be configured to sense current by using
a current transformer (CT) connected to Pin 8. In this case, the
resistive current sense is disabled. A separate single-ended
amplifier has two possible sensitivities that are selected via the
SMBus. If the CT option is selected, the gain of the 1.0, 2.1
buffer that follows the gain trim stage is no longer configurable
and is fixed at 1.0.
The share driver amplifier has a total of 100 mV positive offset
built into it. In order to use the ADM1041 in CT mode, it is
necessary to compensate for this additional 100 mV offset. This
is achieved by adding in a positive offset on the CT input. This
also allows any negative amplifier offsets in the CT chain to be
nulled out.
This offset cancellation is achieved by sourcing a current
through a resistance on the ICT pin. The resistor value is 40 k?
and so for 100 mV of offset cancellation a current of 2.5 μA is
required. It is possible to fine trim this current via Register 15h,
CURRENT SENSE CALIBRATION
Regardless of which means is used to sense the current, the end
result of the calibration process should produce the standard
current share signal between Pins 20 and 23, that is, 2.0 V at
100% load, excluding any additional share signal offset that
might be configured.
CURRENT LIMIT ERROR AMPLIFIER
This is a low gain transconductance amplifier that takes its
input from one of the calibrated current stages described
previously. The amplifier requires only the output pin for loop
compensation, which typically consists of a series RC network
to common. A trimmable reference provides a wide range of
adjustment for the current limit. When the current signal
reaches the reference voltage, the output of the error amplifier
comes out of saturation and begins to drive a controlled current
source. The control threshold is nominally 1.0 V. This current
flows through a resistor in series with the trimmed voltage loop
signal and thereby attempts to increase the voltage signal above
the 1.5 V reference for that loop. The closed voltage loop reacts
by reducing the power supply’s output voltage and this results in
OVERCURRENT PROTECTION
When the current limit threshold is reached, the OCP
comparator detects when the current error amplifier comes out
of saturation. Its threshold is nominally 0.5 V. This starts a timer
that, when it times out, causes an OCP condition to occur and
the power supply to shut down. If the current limit disappears
before the time has expired, the timer is reset. The time period
is configurable via the SMBus. Undervoltage blanking is applied
Bits 4–0, step size 170 nA. For example, 2.5 μA ≈ 15 × 170 nA;
so the code for Register 15h is decimal 15 or 0Fh. Refer to the
Current Transformer parameter in the Specifications table for
Rev. A | Page 22 of 64
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1041AARQZ | IC SECONDARY SIDE CTRLR 24QSOP |
| ADM1060ARU | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1041ARQ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。