- 您现在的位置：买卖IC网 > PDF目录1774 > ADM1041AARQZ-REEL7 (Analog Devices Inc)IC SECONDARY SIDE CTRLR 24QSOP PDF资料下载
参数资料
| 型号： | ADM1041AARQZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/64页 |
| 文件大小： | 0K |
| 描述： | IC SECONDARY SIDE CTRLR 24QSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 1,000 |
| 应用： | 次级侧控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
| 配用： | ADM1041-EVAL-ND - BOARD EVALUATION ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
ADM1041
CURRENT SHARE
The current share method is the master–slave type, which
means that the power supply with the highest output current
automatically becomes the master and controls the share bus
signal. All other power supplies become slaves, and the share
bus signal causes them to increase their output voltages slightly
until their output currents are almost equal to that of the master.
This scheme has two major advantages. A failed master power
supply simply allows one of the slaves to become the new
master. A short circuited share signal disables current sharing,
but all power supplies default to their normal voltage setting,
allowing a certain degree of passive sharing. Because this chip
uses a low voltage process, an external bidirectional amplifier is
needed for most existing share bus signal levels. The voltage
between Pins 20 and 23 is always controlled to 2.0 V full scale,
ignoring any offset. By connecting Pins 20 and 23 together, the
chip can produce a 2.0 V share signal directly without any exter-
nal circuits. To improve accuracy, the share signal is referenced
to remote voltage sense negative.
CURRENT SHARE OFFSET
To satisfy some customer specifications, the current share signal
can be offset by a fixed amount by using a trimmable current
generator and a series resistor. The offset is added on top of the
I SHARE DRIVE AMPLIFIER
This amplifier is a buffer with enough current source capability
to drive the current share circuits of several slave power supplies.
It has negligible current sink capability. Refer to the Differential
DIFFERENTIAL SENSE AMPLIFIER
This amplifier has unity gain and senses the difference between
the share bus voltage and the remote voltage sense negative pin.
When the power supply is the master, it forms a closed loop
with the I SHARE drive amplifier described above, and therefore it
causes the share bus voltage between Pins 20 and 23 to equal the
current share signal at the noninverting input of the I SHARE drive
amplifier. When the power supply is a slave, the output of the
differential sense amplifier exceeds the internal current share
signal, which causes the I SHARE drive amplifier to be driven into
cutoff. Because it is not possible to trim out negative offsets in
the op amps in the current share chain, a 50 mV voltage source
is used to provide a known fixed positive offset. The share bus
I SHARE ERROR AMPLIFIER
This is a low gain transconductance amplifier that measures the
difference between the internal current share voltage and the
signal voltage on the external share bus. If two power supplies
have almost identical current share signals, a 50 mV voltage
source on the inverting input helps arbitrate which power
supply becomes the master and prevents “hunting” between
master and slave roles. The amplifier requires only the output
pin for loop compensation, which typically consists of a series
RC network to common. When the power supply is a slave, the
output of the error amplifier comes out of saturation and begins
to drive a controlled current sink. The control threshold is
nominally 1.0 V. This current flows from a resistor in series with
the trimmed voltage loop signal and thereby attempts to decrease
the voltage signal below the 1.5 V reference for that loop. The
closed voltage loop reacts by increasing the power supply’s
output voltage until current share is achieved. The maximum
current sink is limited so that the power supply voltage can be
increased only a small amount, which is usually limited to be
within the customer’s specified voltage regulation limit. This
small voltage increase also limits the control range of the current
share circuit and is called the capture range. The capture range
may be set via the SMBus to one of four values, from 1% to 4%
I SHARE CLAMP
This clamp keeps the current share-loop compensation capacitor
discharged when the current share is not required to operate.
The clamp is released during power-up when the voltage refer-
ence and therefore the output voltage of the power supply has
risen to either 75% or 88% of its final value. This is configurable
via the SMBus. When the clamp is released, the current share
loop slowly “walks in” the current share and helps to avoid
Share_OK DETECTOR
Incorrect current sharing is a useful early indicator that there is
some sort of non-catastrophic problem with one of the power
supplies in a parallel system. Two comparators are used to detect
an excessive positive or negative error voltage at the input of the
I SHARE error amplifier, which indicates that the current share
loop has lost control. One of four possible error levels must be
offset controlled current source must be trimmed via the
Rev. A | Page 24 of 64
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1041AARQZ | IC SECONDARY SIDE CTRLR 24QSOP |
| ADM1060ARU | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1041ARQ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。