- 您现在的位置：买卖IC网 > PDF目录1774 > ADM1041AARQZ-REEL7 (Analog Devices Inc)IC SECONDARY SIDE CTRLR 24QSOP PDF资料下载
参数资料
| 型号： | ADM1041AARQZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 33/64页 |
| 文件大小： | 0K |
| 描述： | IC SECONDARY SIDE CTRLR 24QSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 1,000 |
| 应用： | 次级侧控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
| 配用： | ADM1041-EVAL-ND - BOARD EVALUATION ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
ADM1041
SMBus SERIAL PORT
The programming and microprocessor interface for the
ADM1041 is a standard SMBus serial port, which consists of a
clock line and a data line. The more rigorous requirements of
MICROPROCESSOR SUPPORT
The ADM1041 has many features that allow it to operate with
the aid of a microprocessor. There are several reasons why a
microprocessor might be used:
the SMBus standard are specified in order to give the greatest
noise immunity. The ADM1041 operates in slave mode only. If a
microprocessor is not used, these pins can be configured to
perform the PS ON LINK and AC_OKLink functions. Note that
this port is not intended to be connected to the customer’s
SMBus (or I 2 C bus). Continuous SMBus activity or an external
bus fault interferes with the inter-ASIC communication, possibly
preventing proper operation and proper fault reporting. If the
customer needs status and control functions via the SMBus, it is
recommended that a microprocessor with a hardware SMBus
(I 2 C) port be used for this interface. The microprocessor should
access the ASICs via a second SMBus port, which may be emu-
lated in software (subset of the full protocol).
SDA/PS ON LINK
The SDA pin normally carries data in and out of the ASIC
during programming/configuration or while reading/writing by
a microprocessor. If a microprocessor is not used, this pin can
be configured as PS ON LINK and can be connected to the same
pin on other ADM1041s in the power supply. If a fault is
detected in any ADM1041, causing it to shut down, it uses this
pin to signal the other ADM1041s to also shut down. If an auto-
restart has been configured, it also causes all ADM1041s to turn
on together.
?
?
?
?
?
?
To provide unusual logic and/or timing requirements,
particularly for fault conditions.
To drive one or more LEDs, including flashing, according
to the status of the power supply.
To replace other discrete circuits such as multiple OTP,
extra output monitoring, fan speed control, and failure
detection, and combine the status of these circuits with the
status of the ADM1041s.
To free up some pins on the ADM1041s. This could reduce
the number of ASICs and therefore the cost.
To interface to an external SMBus (or I 2 C) for more
detailed status reporting. The SMBus port in the ADM1041
is not intended for this purpose.
To allow EEPROM space in ADM1041(s) or in the
microprocessor to be used for FRU (VPD) data. A simple
or complex microprocessor can be used according to the
amount of additional functionality required. Note that the
microprocessor is not intended to access or modify the
EEPROM address space that is used for the configuration
of the ADM1041(s).
SCL/AC_OKLink
The SCL pin normally provides a clock signal into the ASIC
during programming/configuration or while reading/writing by
a microprocessor. If a microprocessor is not used, this pin can
be configured as AC_OKLink, and can be connected to the
same pin on other ADM1041s in the power supply. This allows
a single ADM1041 to be used for ac sensing and helps to
synchronize the start-up of multiple ADM1041s.
ADD0
This pin configures two bits of the chip address for the SMBus.
It is three-level and can be pulled high to V DD , pulled low to
ground, or left floating (internally biased to 2.5 V). An additional
bit may be set during configuration, which allows up to six
ADM1041s to be used in a single power supply. The state of
ADD0 is continuously sampled after V DD power-up. After the
first time the ADM1041 is successfully addressed, the internal
bias is released and ADD0 becomes high impedance.
Interfacing
The microprocessor must access the ADM1041(s) via their
on-board SMBus (I 2 C) port. Since this port is also used for
configuration of the ADM1041(s), the software must include a
routine that avoids SMBus activity during the configuration
process. The simplest interface is for the microprocessor to have
an SMBus (I 2 C) port implemented in hardware, but this may be
more expensive. An alternative is to emulate the bus in software
and to use two general-purpose logic I/O pins. Only a simple
subset of the SMBus protocol need be emulated because the
ADM1041 always operates as a slave device.
Configuring for a Microprocessor
Except during initial configuration, all ADM1041 registers that
need to be accessed are high speed CMOS devices that do not
involve EEPROM. The Microprocessor Support table (Table 43)
details the various registers, bits, and flags that can be read and
written to, including explanations.
Note that for the microprocessor to gain control of the PSON
and AC SENSE functions, the normal signal path in the ADM1041
must be configured to be broken. A separate configuration bit is
allocated to each signal. The microprocessor can then write to
the signal after the break as though the signal originated within
the ADM1041 itself. The original signals can still be read prior
to the break.
Rev. A | Page 33 of 64
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1041AARQZ | IC SECONDARY SIDE CTRLR 24QSOP |
| ADM1060ARU | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM1041ARQ-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。