参数资料
| 型号： | ADM1041AARQZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/56页 |
| 文件大小： | 0K |
| 描述： | IC SECONDARY SIDE CTRLR 24QSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 56 |
| 应用： | 次级侧控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 管件 |
| 配用： | ADM1041-EVAL-ND - BOARD EVALUATION ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADM1041A
Mnemonic
DC_OK
AC_OK
DC_OK on delay
DC_OK off delay
Debounce Digital Noise
Filter
ACSENSE1
Pulse OK
AC Hysteresis
ACSENSE2
Soft-Start
VDD–OVP
VDD–UVL
Auto Restart Mode
VREF–MON
GND–MON
Description
The DC_OK function advises the system on the status of the power supply. When it is false, the system is
assured of at least 1 ms of operation if ac power is lost for any reason. Other turn-off modes provide more
warning time. This pin is an open-drain output. It can be configured as a P-channel pull-up or an N-channel
pull-down. It may also be configured as positive or negative (inverted) logic.
The AC_OK function advises the system whether or not sufficient bulk voltage is present to allow reliable
operation. The system may choose to shut down if this pin is false. The power supply normally tries to
maintain normal operation as long as possible, although DC_OK goes false when only a millisecond or so of
operation time is left. This pin is an open-drain output. It can be configured as a P-channel pull-up or an N-
channel pull-down. It may also be configured as positive or negative (inverted) logic.
The DC_OK output is kept false for typically 100 ms to 900 ms during power-up.
When the system is to be shut down in response to PSON going low, or in response to an OCP or OTP event, a
signal is first sent to the DC_OK output to go false as a warning that power is about to be lost. PEN is signaled
false typically 2 ms later (configurable).
All of the inputs to the logic core are first debounced or digitally filtered to improve noise immunity. The
debounce period for OV events is in the order of 16 μs, for UV events it is 450 μs, and for PSON it is typically
80 ms (configurable).
A voltage from the secondary of the power transformer, which can provide an analog of the bulk supply, is
rectified and lightly filtered and measured by the ac sense function. At start-up, if this voltage is adequate,
this function signals the end-user system that it is okay to start. If a brown-out occurs or ac power is removed,
this function can provide early warning that power is about to be lost and allow the system to shut down in
an orderly manner. While ACSENSE is low, UVB is enabled, which means undervoltage protection is not
initiated. If ac power is so low that the converter cannot continue to operate, other protection circuits on the
primary side normally shut down the converter. When an adequate voltage level is resumed, a power-up
cycle is initiated.
As well as providing ACSENSE, the preceding connection to the transformer is used to gate the operation of
the OrFET circuit. If the output of the transformer is good, the OrFET circuit allows gate drive to the OrFET.
ACSENSE Hysteresis. Configurable voltage on the ACSENSE input allows the ACSENSE upper and lower
threshold to be adjusted to suit different amounts of low frequency ripple present on the bulk capacitor.
An alternate form of ac sense can be accepted by the ADM1041A. This may in the form of an opto-coupled
signal from the primary side where the actual level sensing might be done. As with the above, while ac is low
and UVB is disabled, AC_OK is false and DC_OK is true. Any brownout protection that might be required on
the primary is done on the primary side.
At start-up, the voltage reference to the voltage error amplifier is brought up slowly in approximately 127
steps to provide a controlled rate of rise of the output voltage.
An OVP fault on the auxiliary supply to the ADM1041A causes a standard OVP operation (see the OVP
function in this table).
A UVL fault on the auxiliary supply to the IC causes a standard UVP operation (see the UVP function in this
table).
In this mode, the housekeeping circuit attempts to restart the supply after an undervoltage event at about 1
second intervals. No other fault can initiate auto-restart.
The internal precision reference is monitored by a separate reference for overvoltage and allows truly
redundant OVP. The externally available reference is also monitored for an undervoltage that would indicate
a short on the pin.
The internal ground is constantly monitored against the VS- pin. If the chip ground goes positive with respect
to this pin, it indicates that the chip ground is open-circuit either inside the ADM1041A or the external wiring.
The ADM1041A would be latched off, similar to an OV event.
Rev. 0 | Page 17 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1060ARU | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
| ADM1065ASUZ | IC SEQUENCER/MONITOR 48-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041AARQZ-REEL | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041AARQZ-REEL7 | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。