参数资料
| 型号： | ADM1041AARQZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 37/56页 |
| 文件大小： | 0K |
| 描述： | IC SECONDARY SIDE CTRLR 24QSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 56 |
| 应用： | 次级侧控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 管件 |
| 配用： | ADM1041-EVAL-ND - BOARD EVALUATION ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADM1041A
EXTENDED SMBus ADDRESSING
It is possible to use more than three ADM1041As in a single
power supply. The first time the device is powered up, Bit 1 of
Configuration Register 1 (ADD1) is 0. This means that only
three device addresses are initially available as defined by
ADD0; if there are more than three devices in a system, two or
To overcome this, the ICT pin has additional functionality.
Taking ICT below GND temporarily disables the SMBus
function of the device. Thus, if the ICT pin of all devices in
which ADD1 is to remain 0 are taken negative, the ADD1 bits
BACKDOOR ACCESS
After SCL and SDA have been configured as AC_OKLink and
PS ON LINK, it may be desired to recover the SMBus access to
the ADM1041A. Changes may be necessary to the internal
configuration or trim bits. This is achieved by holding the SCL
and SDA pins at 0 V (ground) while cycling V DD . SCL and SDA
V DD
of all other devices can be set to 1 via the SMBus. Each device
then has a unique address. Internal diodes clamp the negative
voltage to about 0.6 V, and care should be taken to limit the
ICT 8
SCL 13
AC_OKLink
PS ON LINK
current to less than approximately 5 mA on each ICT input to
N/C 15 ADD0
SDA 14
prevent the possibility of damage or latch-up. The suggested
current is 3 mA. One example of a suitable circuit is given in
DEVICE 5
ICT 8
trimmed. If required, AC_OKLink and PS ON LINK must be
configured last. If ICT is used for its intended purpose as a
current transformer input, care must be taken with the circuit
design to allow the extended SMBus addressing to work.
SDA/PS ON LINK
The SDA pin normally carries data in and out of the
ADM1041A during programming/configuration or while
reading/writing by a microprocessor. If a microprocessor is not
used, this pin can be configured as PS ON LINK and can be
connected to the same pin on other ADM1041As in the power
supply. If a fault is detected in any ADM1041A, causing it to
shut down, it uses this pin to signal the other ADM1041As to
also shut down. If an auto-restart has been configured, it also
ADD1 = 1
V DD
SCL 13
SDA 14
15 ADD0
DEVICE 4
ICT 8
SCL 13
SDA 14
15 ADD0
DEVICE 3
ICT 8
SCL 13
4k Ω
causes all ADM1041As to turn on together.
N/C 15 ADD0
SDA 14
2.4mA
SCL/AC_OKLink
DEVICE 2
The SCL pin normally provides a clock signal into the
ADM1041A during programming/configuration or while
ICT 8
4k Ω
EXTENDED
SMBus
ADDRESSING
reading/writing by a microprocessor. If a microprocessor is not
used, this pin can be configured as AC_OKLink, and can be
connected to the same pin on other ADM1041As in the power
ADD1 = 0
V DD
15 ADD0
SCL 13
SDA 14
–12V
supply. This allows a single ADM1041A to be used for ac
DEVICE 1
sensing and helps to synchronize the start-up of multiple
ADM1041As.
15 ADD0
ICT 8
SCL 13
SDA 14
4k Ω
DEVICE 0
BACKDOOR
Figure 38. Extended SMBus Addressing and Backdoor Access
Rev. 0 | Page 37 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1060ARU | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
| ADM1065ASUZ | IC SEQUENCER/MONITOR 48-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041AARQZ-REEL | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041AARQZ-REEL7 | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。