参数资料
| 型号： | ADM1041AARQZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 25/56页 |
| 文件大小： | 0K |
| 描述： | IC SECONDARY SIDE CTRLR 24QSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 56 |
| 应用： | 次级侧控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 管件 |
| 配用： | ADM1041-EVAL-ND - BOARD EVALUATION ADM1041 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADM1041A
OrFET GATE DRIVE
When configured, this block provides a signal to turn on/off
an OrFET used in the output of paralleled power supplies. The
gate drive voltage of one of these FETs is typically 6 V to 10 V
above the output voltage. Because the output voltage of the
ADM1041A is limited, an external transistor needs to be used.
The block diagram shows an example of this approach.
The F G output is an open-drain, N-channel MOSFET and is
normally high, which holds the OrFET off. When all the start-
up conditions are correct, Pin 19 is pulled low, which allows the
OrFET to turn on. The logic can also be configured as inverted
if a noninverting drive circuit is used.
A differential amplifier monitors the voltage across the OrFET
and has two major functions. First, during start-up, it allows the
OrFET to turn on with almost 0 V across it to avoid voltage
glitches on the bus. This applies to a hot bus or a cold bus. The
internal threshold can be configured from 20 mV to 50 mV
(negative), which is scaled up by the external voltage dividers.
Second, if a rectifier or filter capacitor fails during steady state
operation, it detects the resulting reverse voltage across the
OrFET’s on-resistance and turns off the OrFET before a voltage
dip appears on the bus. The internal threshold can be
configured from 100 mV to 250 mV (negative), which is also
scaled up by the external voltage dividers. A slightly larger filter
capacitor may be used on the voltage divider at Pin 6 to speed
up this function.
such an event. In the plot, V FD is ramped down and the response
time of the F G pin to a reverse voltage event on the F D pin is
seen. This simulates the rectifier or filter capacitor failure
during steady-state operation. When the F D voltage is below
1.9 V (2 V minus 100 mV threshold), the F G pin reacts. As can
be seen, the response time is approx 330 nsecs. This extremely
fast turn-off is vital in an n+1 power supply system
configuration. It ensures that the damaged power supply
removes itself from the system quickly. Figure 18 shows the
equivalent response time to turn on the OrFET. As can be seen,
turn-on time when the F G pin polarity is inverted. As can be
seen, to turn off the OrFET, the V FG pin now transitions from
high to low. Also, its corresponding turn-on event occurs from
a low-to-high transition. The circuit in Figure 21 is used to
generate these plots.
T TOTAL = 330ns
64%
T DELAY = 218ns T = 112ns
Figure 17. OrFET Turn-Off Time (Default Polarity)
T TOTAL = 506ns
Figure 18. OrFET Turn-On Time (Default Polarity)
there is a delay of approximately 500 ns before the FG pin
ramps down to turn on the OrFET, allowing the power supply
to contribute to the system. This propagation delay is due
mainly to internal amplifier response limitations. The circuit in
Figure 21 is used to generate these plots. In this case, the
resistor to V DD from the FG pin is 2 kΩ.
Rev. 0 | Page 25 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1060ARU | IC SUPERVIS/SEQUENC 7-CH 28TSSOP |
| ADM1062ACPZ-REEL7 | IC SEQUENCER/SUPERVISOR 40LFCSP |
| ADM1063ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ADM1064ACPZ | IC SEQUENCER/SUPERVISOR 40-LFCSP |
| ADM1065ASUZ | IC SEQUENCER/MONITOR 48-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1041AARQZ-REEL | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041AARQZ-REEL7 | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADM1041ARQ | 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1041ARQ-2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。