- 您现在的位置：买卖IC网 > PDF目录17406 > ADP1877HC-EVALZ (Analog Devices Inc)BOARD EVALUATION 13A ADP1877 PDF资料下载
参数资料
| 型号： | ADP1877HC-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION 13A ADP1877 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.05V，1.8V |
| 电流 - 输出： | 13A |
| 输入电压： | 6 ~ 14 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 600kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP1877 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
APPLICATIONS INFORMATION
SETTING THE OUTPUT VOLTAGE
The output voltage is set using a resistive voltage divider from
the output to FB. The voltage divider divides down the output
voltage to the 0.6 V FB regulation voltage to set the regulation
output voltage. The output voltage can be set to as low as 0.6 V
and as high as 90% of the power input voltage.
The maximum input bias current into FB is 100 nA. For a 0.15%
degradation in regulation voltage and with 100 nA bias current,
the low-side resistor, R BOT , must be less than 9 kΩ, which results
in 67 μA of divider current. For R BOT , use a 1 kΩ to 20 kΩ resistor.
A larger value resistor can be used but results in a reduction in
output voltage accuracy due to the input bias current at the FB
pin, while lower values cause increased quiescent current
consumption. Choose R TOP to set the output voltage by using
the following equation:
ADP1877
The SSx pin reaches a final voltage equal to VCCO. If the output
voltage is precharged prior to turn-on, the ADP1877 prevents
reverse inductor current, which discharges the output capacitor.
Once the voltage at SSx exceeds the regulation voltage (typically
0.6 V), the reverse current is reenabled to allow the output
voltage regulation to be independent of load current.
When a controller is disabled, for instance, EN1/EN2 is pulled
low or experiences an overcurrent limit condition, the soft start
capacitor is discharged through an internal 1 kΩ pull-down
resistor.
SETTING THE CURRENT LIMIT
The current limit comparator measures the voltage across the
low-side MOSFET to determine the load current.
The current limit is set by an external current limit resistor,
R ILIM . The current sense pin, ILIMx, sources 50 μA to this external
R TOP = R BOT ? ? OUT
?
?
? V ? V FB
? V FB
?
?
resistor. This creates an offset voltage of R ILIM multiplied by
50 μA. When the drop across the low-side MOSFET, R DSON , is
equal to or greater than this offset voltage, the ADP1877 flags a
where:
R TOP is the high-side voltage divider resistance.
R BOT is the low-side voltage divider resistance.
V OUT is the regulated output voltage.
V FB is the feedback regulation threshold, 0.6 V.
The minimum output voltage is dependent on f SW and minimum
DH on time. The maximum output voltage is dependent on f SW ,
the minimum DH off time, and the IR drop across the high-side
current limit event.
Because the ILIMx current and the MOSFET, R DSON , vary over
process and temperature, the minimum current limit should be
set to ensure that the system can handle the maximum desired
load current. To do this, use the peak current in the inductor,
which is the desired output current limit level plus ? of the
ripple current, the maximum R DSON of the MOSFET at its
highest expected temperature, and the minimum ILIM current.
N-channel MOSFET (NMOSFET) and the DCR of the inductor.
For example, with an f SW of 600 kHz (or 1.67 μs) and minimum on
time of 130 ns, the minimum duty cycle is approximately 7.8%
R ILIM =
I LPK × R DSON _ MAX
40 μ A
(130 ns/1.67 μs). If V IN is 12 V and the duty cycle is 7.8%, then
the lowest output is 0.94 V. As an example for the maximum output
voltage, if V IN is 5 V, f SW is 600 kHz, and the minimum DH off
time is 390 ns (330 ns DH off time plus approximately 60 ns
total dead time), then the maximum duty cycle is 76%. Therefore,
the maximum output is approximately 3.8 V. If the IR drop
across the high-side NMOSFET and the DCR of the inductor is
0.5 V, then the absolute maximum output is 4.5 V (5 V ? 0.5 V),
independent of f SW and duty cycle.
SOFT START
Program the soft start by connecting a capacitor from SSx to
AGND. The soft start function limits the input inrush current
and prevents the output overshoot.
On startup, a 6.5 μA current source charges the SSx capacitor.
The soft start period is approximated by
where:
I LPK is the peak inductor current.
The buck converters usually run a fairly high current. PCB
layout and component placement may affect the current limit
setting. An iteration of the R ILIM value may be required for a
particular board layout and MOSFET selection. If alternative
MOSFETs are substituted at some point in production, these
resistor values may also need an iteration. Keep in mind that the
temperature coefficient of the MOSFET, R DSON , is typically
0.4%/ o C.
t SS =
0 . 6 V
6 . 5 μ A
C SS
Rev. D | Page 17 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| EYM06DTMD-S189 | CONN EDGECARD 12POS R/A .156 SLD |
| LM4040B30IDBZR | IC VREF SHUNT PREC 3V SOT-23-3 |
| RBB05DHFD | CONN EDGECARD 10POS .050 SMD |
| ADP2108-2.5-EVALZ | BOARD EVALUATION ADP2108 2.5V |
| LQH43CN4R7M03L | INDUCTOR 4.7UH 20% 750MA 1812 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1878 | 制造商:AD 制造商全称:Analog Devices 功能描述:Synchronous Buck Controller |
| ADP1878-0.3-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Synchronous Buck Controller |
| ADP1878-0.6-EVALZ | 功能描述:BOARD EVAL FOR ADP1878-0.6 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADP1878-1.0-EVALZ | 功能描述:BOARD EVAL FOR ADP1878-1.0 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADP1878ACPZ-0.3-R7 | 功能描述:IC REG CTRLR BUCK PWM CM 14LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。