- 您现在的位置：买卖IC网 > PDF目录298814 > ADS1298RIZXGT (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PBGA64 PDF资料下载
参数资料
| 型号： | ADS1298RIZXGT |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA64 |
| 封装： | 8 X 8 MM, LEAD FREE, PLASTIC, NFBGA-64 |
| 文件页数： | 26/87页 |
| 文件大小： | 1430K |
| 代理商： | ADS1298RIZXGT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页
CS
SCLK
DRDY
DOUT
STAT
24-Bit
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
216SCLKs
DIN
SBAS459H
– JANUARY 2010 – REVISED MAY 2011
Data Output (DOUT)
The data output pin (DOUT) is used with SCLK to read conversion and register data from the ADS129x. Data on
DOUT are shifted out on the rising edge of SCLK. DOUT goes to a high-impedance state when CS is high. In
read data continuous mode (see the SPI Command Definitions section for more details), the DOUT output line
also indicates when new data are available. This feature can be used to minimize the number of connections
between the device and the system controller.
Figure 37 shows the data output protocol for ADS1298.
Figure 37. SPI Bus Data Output for the ADS1298 (Eight Channels)
Data Retrieval
Data retrieval can be accomplished in one of two methods. The read data continuous command (see the
RDATAC: Read Data Continuous section) can be used to set the device in a mode to read the data continuously
without sending opcodes. The read data command (see the RDATA: Read Data section) can be used to read
just one data output from the device (see the SPI Command Definitions section for more details). The conversion
data are read by shifting the data out on DOUT. The MSB of the data on DOUT is clocked out on the first SCLK
rising edge. DRDY returns to high on the first SCLK falling edge. DIN should remain low for the entire read
operation.
The number of bits in the data output depends on the number of channels and the number of bits per channel.
For the ADS1298/8R, the number of data outputs is (24 status bits + 24 bits
× 8 channels) = 216 bits. The format
of the 24 status bits is: (1100 + LOFF_STATP + LOFF_STATN + bits[4:7] of the GPIO register). The data format
for each channel data are twos complement and MSB first. When channels are powered down using the user
register setting, the corresponding channel output is set to '0'. However, the sequence of channel outputs
remains the same. For the ADS1294/4R and ADS1296/6R, the last four and two channel outputs shown in
Figure 37 are zeros. The four and six channels parts require only 120 and 168 SCLKs to shift data out,
respectively. Status and GPIO register bits are loaded into the 24-bit status word 2tCLKs before DRDY goes low.
The ADS129x also provide a multiple readback feature. The data can be read out multiple times by simply giving
more SCLKs, in which case the MSB data byte repeats after reading the last byte. The DAISY_EN bit in
CONFIG1 register must be set to '1' for multiple readbacks.
Data Ready (DRDY)
DRDY is an output. When it transitions low, new conversion data are ready. The CS signal has no effect on the
data ready signal. The behavior of DRDY is determined by whether the device is in RDATAC mode or the
RDATA command is being used to read data on demand. (See the RDATAC: Read Data Continuous and
RDATA: Read Data subsections of the SPI Command Definitions section for further details).
When reading data with the RDATA command, the read operation can overlap the occurrence of the next DRDY
without data corruption.
The START pin or the START command is used to place the device either in normal data capture mode or pulse
data capture mode.
32
Copyright
2010–2011, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| ADSP-1401TN/883B | 16-BIT, MICROPROGRAM SEQUENCER, PDIP48 |
| ADSP-21160NCB-100 | 64-BIT, 50 MHz, OTHER DSP, PBGA400 |
| ADSP-21365YSWZ-2BA | 16-BIT, 55.55 MHz, OTHER DSP, PQFP144 |
| ADSP-2181BS-160 | 24-BIT, 20 MHz, OTHER DSP, PQFP128 |
| ADUC845BCPZ8-3 | 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, QCC56 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADS1299 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Low-Noise, 8-Channel, 24-Bit Analog Front-End for Biopotential Measurements |
| ADS1299_1211 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Low-Noise, 8-Channel, 24-Bit Analog Front-End for Biopotential Measurements |
| ADS1299-4PAG | 功能描述:IC AFE 4-CH 24BIT 64TQFP 制造商:texas instruments 系列:- 包装:托盘 零件状态:在售 位数:24 通道数:4 电压 - 电源，模拟:5V 电压 - 电源，数字:1.8 V ~ 3.6 V 封装/外壳:64-TQFP 供应商器件封装:64-TQFP（10x10） 标准包装:160 |
| ADS1299-4PAGR | 功能描述:IC AFE 4-CH 24BIT 64TQFP 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:在售 位数:24 通道数:4 功率（W）:24mW 电压 - 电源，模拟:4.75 V ~ 5.25 V 电压 - 电源，数字:1.8 V ~ 3.6 V 封装/外壳:64-TQFP 供应商器件封装:64-TQFP（10x10） 标准包装:1 |
| ADS1299-6PAG | 功能描述:IC AFE 6-CH 24BIT 64TQFP 制造商:texas instruments 系列:- 包装:托盘 零件状态:在售 位数:24 通道数:6 功率（W）:33mW 电压 - 电源，模拟:5V 电压 - 电源，数字:1.8 V ~ 3.6 V 封装/外壳:64-TQFP 供应商器件封装:64-TQFP（10x10） 标准包装:160 |
发布紧急采购，3分钟左右您将得到回复。