参数资料
型号: ADT7490ARQZ-R7
厂商: ON Semiconductor
文件页数: 25/75页
文件大小: 0K
描述: IC THERM MON FAN CTLR 24-QSOP
产品变化通告: MFG CHG Notification ADI to ON Semi
QSOP 24ld Pkg (MSL) Change 17/Jun/2010
Product Discontinuation 30/Sept/2011
标准包装: 1,000
系列: dBCool®
功能: 风扇控制,温度监控器
传感器类型: 内部和外部
感应温度: -40°C ~ 125°C
精确度: ±1.5°C(最小值)
拓扑: ADC,比较器,风扇速度计数器,多路复用器,寄存器库
输出类型: SMBus?
输出警报:
输出风扇:
电源电压: 3 V ~ 3.6 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 24-SSOP(0.154",3.90mm 宽)
供应商设备封装: 24-QSOP
包装: 带卷 (TR)
ADT7490
Enabling the SMBALERT Interrupt Output
The SMBALERT interrupt function is disabled by
default. Pin 10 or Pin 14 can be reconfigured as an
SMBALERT output to signal out-of-limit conditions.
Table 28. CONFIGURING PIN 10 AS SMBALERT
OUTPUT
works only if the fan is already running, for example, in
manual mode when the current duty cycle is above 0x00, or
in automatic mode when the temperature is above T MIN .
If the temperature is below T MIN or if the duty cycle in
manual mode is set to 0x00, pulling the THERM low
externally has no effect. See Figure 32 for more information.
Register
Configuration Register 3
(Register 0x78), Bit 0
Bit Setting
[1] Pin 10 = SMBALERT
[0] Pin 10 = PWM2 (Default)
T MIN
Assigning THERM Functionality to a Pin
Pin 14 on the ADT7490 has three possible functions:
SMBALERT, THERM, and TACH4. The user chooses the
required functionality by setting Bit 0 and Bit 1 of
Configuration Register 4 at Address 0x7D.
If THERM is enabled (Bit 1, Configuration Register 3
at Address 0x78),
? Pin 22 becomes THERM.
? If Pin 14 is configured as THERM (Bit 0 and Bit 1 of
Configuration Register 4 at Address 0x7D), THERM is
enabled on this pin.
If THERM is not enabled,
THERM
THERM ASSERTED TO LOW AS
AN INPUT: FANS DO NOT GO
TO 100% BECAUSE TEMPERATURE THERM ASSERTED TO LOW AS
IS BELOW T MIN AN INPUT: FANS GO TO 100%
BECAUSE TEMPERATURE IS
ABOVE T MIN AND FANS ARE
ALREADY RUNNING.
Figure 32. Asserting THERM Low as an Input in
Automatic Fan Speed Control Mode
?
Pin 22 becomes a 2.5 V IN measurement input.
? If Pin 14 is configured as THERM, THERM is disabled
on this pin.
Table 29. CONFIGURING PIN 14 IN REGISTER 0x7D
THERM Timer
The ADT7490 has an internal timer to measure THERM
assertion time. For example, the THERM input can be
connected to the PROCHOT o utput   of a CPU to measure
Bit 1
0
0
1
1
Bit 0
0
1
0
1
Function
TACH4
THERM
SMBALERT
Reserved
system performance. The THERM input can also
be connected to the output of a trip point temperature sensor.
The timer is started on the assertion of the ADT7490
THERM input and stopped when THERM is deasserted.
The timer counts THERM times cumulatively, that is, the
timer resumes counting on the next THERM assertion. The
THERM as an Input
When THERM is configured as an input, the user can time
assertions on the THERM pin. This can be useful for
connecting to the PROCHOT output of a CPU to gauge
system performance.
The user can also set up the ADT7490 so that the fans run
at 100% when the THERM pin is driven low externally. The
fans run at 100% for the duration of the time that the THERM
pin is pulled low. This is done by setting the BOOST bit
(Bit 2) in Configuration Register 3 (Address 0x78) to 1. This
THERM timer continues to accumulate THERM assertion
times until the timer is read (it is cleared on read), or until it
reaches full scale. If the counter reaches full scale, it stops
at that reading until cleared.
The 8-bit THERM timer status register (0x79) is designed
so that Bit 0 is set to 1 on the first THERM assertion. Once
the cumulative THERM assertion time has exceeded
45.52 ms, Bit 1 of the THERM timer is set and Bit 0 now
becomes the LSB of the timer with a resolution of 22.76 ms
(see Figure 33).
http://onsemi.com
25
相关PDF资料
PDF描述
EBM08DRSN CONN EDGECARD 16POS DIP .156 SLD
ADT7488AARMZ-RL7 IC TEMP/VOLT DGTL W/SST 10MSOP
TPCL225M016R5000 CAP TANT 2.2UF 16V 20% 0603
UF4002 DIODE GPP FAST 1A 100V DO-41
ADT7486AARMZ-R7 IC TEMP SENS DGTL 2CH SST 10MSOP
相关代理商/技术参数
参数描述
ADT7490ARQZ-REEL 功能描述:马达/运动/点火控制器和驱动器 FAN CNTRL W/PECI INT RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
ADT7490ARQZ-REEL7 功能描述:IC THERM MON FAN CTRLR 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统(传感器) 传感器类型:内部和外部 感应温度:-40°C ~ 125°C,外部传感器 精确度:±2.5°C 本地(最大值),±5°C 远程(最大值) 拓扑:ADC,比较器,寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7490ZEVB 功能描述:BOARD EVALUATION FOR ADT7490 RoHS:是 类别:编程器,开发系统 >> 过时/停产零件编号 系列:dBCool® 标准包装:1 系列:- 传感器类型:CMOS 成像,彩色(RGB) 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
ADT75 制造商:AD 制造商全称:Analog Devices 功能描述:+-1∑C Accurate, 12-Bit Digital Temperature Sensor
ADT7516 制造商:AD 制造商全称:Analog Devices 功能描述:SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC