- 您现在的位置：买卖IC网 > PDF目录223348 > Am29LV400T-90RWAEB (Advanced Micro Devices, Inc.) 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | Am29LV400T-90RWAEB |
| 厂商： | Advanced Micro Devices, Inc. |
| 英文描述： | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 4兆位（512亩x 8-Bit/256亩x 16位），3.0伏的CMOS只引导扇区闪存 |
| 文件页数： | 40/40页 |
| 文件大小： | 516K |
| 代理商： | AM29LV400T-90RWAEB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页
9
Am29LV400
PR EL IMIN AR Y
has details on erasing a sector or the entire chip, or
suspending/resuming the erase operation.
After the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in this
mode. Refer to the Autoselect Mode and Autoselect
Command Sequence sections for more information.
ICC2 in the DC Characteristics table represents the ac-
tive current specification for the write mode. The “AC
Characteristics” section contains timing specification
tables and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status
bits on DQ7–DQ0. Standard read cycle timings and ICC
read specifications apply. Refer to “Write Operation
Status” for more information, and to “AC Characteris-
tics” for timing diagrams.
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at VCC ± 0.3 V.
(Note that this is a more restricted voltage range than
VIH.) If CE# and RESET# are held at VIH, but not within
VCC ± 0.3 V, the device will be in the standby mode, but
the standby current will be greater. The device requires
standard access time (tCE) for read access when the
device is in either of these standby modes, before it is
ready to read data.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device
energy consumption. The device automatically
enables this mode when addresses remain stable for
t AC C + 30 ns . The automatic sl eep m ode is
independent of the CE#, WE#, and OE# control
signals. Standard address access timings provide new
data when addresses are changed. While in sleep
mode, output data is latched and always available to
r epres en ts th e au to matic sle ep mod e c u rr ent
specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the RE-
SET# pin is driven low for at least a period of tRP, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VSS±0.3 V, the device
draws CMOS standby current (ICC4). If RESET# is held
at VIL but not within VSS±0.3 V, the standby current will
be greater.
If RESET# is asserted during a program or erase oper-
ation, the RY/BY# pin remains a “0” (busy) until the in-
ternal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The
system can thus monitor RY/BY# to determine whether
the reset operation is complete. If RESET# is asserted
when a program or erase operation is not executing
(RY/BY# pin is “1”), the reset operation is completed
within a time of tREADY (not during Embedded Algo-
rithms). The system can read data tRH after the RE-
SET# pin returns to VIH.
Refer to the AC Characteristics tables for RESET# pa-
rameters and to Figure 13 for the timing diagram.
Output Disable Mode
When the OE# input is at VIH, output from the device is
相关PDF资料 |
PDF描述 |
|---|---|
| AM29LV400T-90RWAC | Ceramic Multilayer Capacitor; Capacitance:100pF; Capacitance Tolerance:+50, -20 %; Working Voltage, DC:100V; Dielectric Characteristic:NP0; Package/Case:1206; Series:W3F; Leaded Process Compatible:Yes |
| AM29LV400B-90RWAC | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV640DH90RZE | 8 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor |
| Am29LV640DL90RZE | 8 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor |
| Am29LV641DH90RZE | 8 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29LV640DH90REI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 90NS 48TSOP - Trays |
| AM29LV640DL90RZI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV640DU-90NI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV640DU90REI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 90NS 48TSOP - Trays |
| AM29LV640DU-90RWHIT | 制造商:Advanced Micro Devices 功能描述:63-BALL FINE-PITCH BALL GRID ARRAY (FBGA) 0.80 MM PITCH, 11 X 12 MM PACKAGE (FBE063) |
发布紧急采购，3分钟左右您将得到回复。