- 您现在的位置：买卖IC网 > Datasheet目录961 > AS5030 DB (ams)BOARD DEMO AS5030 Datasheet资料下载
参数资料
| 型号： | AS5030 DB |
| 厂商： | ams |
| 文件页数： | 24/44页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5030 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 7.5V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AS5030 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
AS5030
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.2.2
16-bit Write Command
These settings are temporary; they cannot be programmed permanently. The settings will be lost when the power supply is removed.
Command
Bin
Hex
D15
D14
D13 D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
EN PROG
10000
10
1
0
0
0
1
1
0
0
1
0
1
0
1
1
1
0
SET PWR
MODE
DIS HYST
10001
10011
11
13
ULP/
LPn
HYS
PSM
0
0
DIS AGC
10101
15
0
0
0
0
0
rst
0
0
0
AGC 5:0
FA
EN PROG command must be sent with a fixed 16-bit code (8CAE H ) to enable subsequent OTP access.
ULP/LP n selects the Ultra-low Power Mode, when bit PSM is set: 0 = Low Power Mode, 1 = Ultra-low Power Mode
PSM enables power saving modes: 0 = normal operation, 1 = reduced power mode selected by bit ULP/LPn
HYS disables the hysteresis of the digital serial and PWM outputs:
0 (default) = 1-bit hysteresis, 1 = no hysteresis
DIS AGC disables the automatic gain control. The AGC will be frozen to a gain setting written in bits AGC 5:0 (D6:D1), bit FA must be set.
rst General Reset: 0 = normal operation, 1 = perform general reset (required after return from reduced power modes)
FA Freeze AGC; 0 = normal operation, 1= freeze AGC with the values stored in bits AGC 5:0. The PWM output will be invalid when bit FA is set.
8.2.3
18-bit OTP Read Commands
Note: To prohibit unintentional access to the OTP register, OTP PROG/write access is only enabled after the EN PROG command has been
sent. OTP access is locked again by sending a RD ANGLE or SET PWR MODE command.
EN PROG need not to be sent before a READ OTP.
During the 18bit OTP read/write transfer, each bit needs 4 clock pulses to be validated.
Command
Bin
Hex
D17
D16
D15
D14 D13 D12 D11 D10 D9 D8
D7
D6
D5
D4
D3
D2
D1
D0
READ OTP 01111
0F
reserved for factory settings
sens
1:0
zero position
7:0
ANALOG
OTP RD
01001
09
reserved for factory settings
sens
1:0
zero position
7:0
READ OTP reads the contents of the OTP register in digital form. The reserved area may contain any value
ANALOG OTP RD reads the contents of the OTP register as an analog voltage at pin PROG
sens reads the sensitivity setting of the Hall elements: 00 = low sensitivity, 11 = high sensitivity
zero position reads the programmed zero position; the actual angle of the magnet which is displayed as 000
www.ams.com/AS5030
Revision 2.4
24 - 44
相关PDF资料 |
PDF描述 |
|---|---|
| AS5048-DB-1.0 | BOARD DEMO AS5048 |
| AS5215 DB | BOARD DEMO AS5215 |
| AS5245 DB | BOARD DEMO AS5245 |
| AS5304-DK-1.0 | BOARD DEMO AS5304 |
| AS5311 DB | BOARD EVAL FOR AS5311 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5030-TS_EK_AB | 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5030 标准包装:1 |
| AS5030-TS_EK_DB | 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 7.5V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5030 标准包装:1 |
| AS50-330K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
| AS50-331K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
| AS50-332K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
发布紧急采购，3分钟左右您将得到回复。