- 您现在的位置：买卖IC网 > Datasheet目录961 > AS5030 DB (ams)BOARD DEMO AS5030 Datasheet资料下载
参数资料
| 型号： | AS5030 DB |
| 厂商： | ams |
| 文件页数： | 37/44页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5030 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 7.5V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AS5030 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页
AS5030
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.9.1
Magnet Placement
Ideally, the center of the magnet, the diagonal center of the IC and the rotation axis of the magnet should be in one vertical line.
The lateral displacement of the magnet should be within
± 0.25mm from the IC package center or ± 0.5mm from the IC center, including
the placement of the chip within the IC package.
The vertical distance should be chosen such that the magnetic field on the die surface is within the specified limits. The typical
distance “z” between the magnet and the package surface is 0.5mm to 1.8mm with the recommended magnet (6mm x 2.5mm). Larger gaps are
possible, as long as the required magnetic field strength stays within the defined limits.
A magnetic field outside the specified range may still produce acceptable results, but with reduced accuracy. The out-of-range condition will be
indicated, when the AGC is at the limits
(AGC= 0: field too strong;
AGC=63=(3F H ): field too weak or missing magnet.
Figure 32. Bz Field Distribution Along the X-Axis of a 6mm? Diametric Magnetized Magnet
Figure 32 shows a cross sectional view of the vertical magnetic field component Bz between the north and south pole of a 6mm diameter
magnet, measured at a vertical distance of 1mm. The poles of the magnet (maximum level) are about 2.8mm from the magnet center, which is
almost at the outer magnet edges. The magnetic field reaches a peak amplitude of ~± 106mT at the poles.
The Hall elements are located at a radius of 1mm (indicated as squares at the bottom of the graph). Due to the side view, the two Hall elements
at the Y-axis are overlapping at X = 0mm, therefore only 3 Hall elements are shown.
At 1mm radius, the peak amplitude is ~± 46mT, respectively a differential amplitude of 92mT.
The vertical magnetic field B z follows a fairly linear pattern up to about 1.5mm radius. Consequently, even if the magnet is not perfectly centered,
the differential amplitude will be the same as for a centered magnet.
For example, if the magnet is misaligned in X-axis by -0.5mm, the two X-Hall sensors will measure 70mT (@x = -1.5mm) and
-22mt (@x = -0.5mm). Again, the differential amplitude is 92mT.
At larger displacements however, the B z amplitude becomes nonlinear, which results in larger errors that mainly affect the accuracy of the
system (see also Figure 34 )
www.ams.com/AS5030
Revision 2.4
37 - 44
相关PDF资料 |
PDF描述 |
|---|---|
| AS5048-DB-1.0 | BOARD DEMO AS5048 |
| AS5215 DB | BOARD DEMO AS5215 |
| AS5245 DB | BOARD DEMO AS5245 |
| AS5304-DK-1.0 | BOARD DEMO AS5304 |
| AS5311 DB | BOARD EVAL FOR AS5311 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5030-TS_EK_AB | 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5030 标准包装:1 |
| AS5030-TS_EK_DB | 功能描述:AS5030 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 7.5V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5030 标准包装:1 |
| AS50-330K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
| AS50-331K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
| AS50-332K-RC | 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Axial Shielded Inductors |
发布紧急采购，3分钟左右您将得到回复。