参数资料
型号: AT89C51ID2-SLSUM
厂商: Atmel
文件页数: 68/157页
文件大小: 0K
描述: IC 8051 MCU FLASH 64K 44PLCC
产品培训模块: MCU Product Line Introduction
标准包装: 972
系列: 89C
核心处理器: 8051
芯体尺寸: 8-位
速度: 60MHz
连通性: I²C,SPI,UART/USART
外围设备: POR,PWM,WDT
输入/输出数: 34
程序存储器容量: 64KB(64K x 8)
程序存储器类型: 闪存
EEPROM 大小: 2K x 8
RAM 容量: 2K x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 44-LCC(J 形引线)
包装: 管件
配用: AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
18
AT89C51ID2
4289C–8051–11/05
Idle Modes
IDLE modes are achieved by using any instruction that writes into PCON.0 bit (IDL)
IDLE modes A and B depend on previous software sequence, prior to writing into
PCON.0 bit:
IDLE MODE A: OscA is running (OscAEn = 1) and selected (CKS = 1)
IDLE MODE B: OscB is running (OscBEn = 1) and selected (CKS = 0)
The unused oscillator OscA or OscB can be stopped by software by clearing
OscAEn or OscBEn respectively.
IDLE mode can be canceled either by Reset, or by activation of any enabled
interruption
In both cases, PCON.0 bit (IDL) is cleared by hardware
Exit from IDLE modes will leave Oscillators control bits (OscEnA, OscEnB, CKS)
unchanged.
Power Down Modes
POWER DOWN modes are achieved by using any instruction that writes into
PCON.1 bit (PD)
POWER DOWN modes A and B depend on previous software sequence, prior to
writing into PCON.1 bit:
Both OscA and OscB will be stopped.
POWER DOWN mode can be cancelled either by a hardware Reset, an external
interruption, or the keyboard interrupt.
By Reset signal: The CPU will restart according to OSC bit in Hardware Security Bit
(HSB) register.
By INT0 or INT1 interruption, if enabled: (standard behavioral), request on Pads
must be driven low enough to ensure correct restart of the oscillator which was
selected when entering in Power down.
By keyboard Interrupt if enabled: a hardware clear of the PCON.1 flag ensure the
restart of the oscillator which was selected when entering in Power down.
Table 20. Overview
PCON.1
PCON.0
OscBEn
OscAEn
CKS
Selected Mode
Comment
00
0
1
NORMAL MODE
A, OscB stopped
Default mode after power-up or
Warm Reset
00
1
NORMAL MODE
A, OscB running
Default mode after power-up or
Warm Reset + OscB running
00
1
0
NORMAL MODE
B, OscA stopped
OscB running and selected
00
1
0
NORMAL MODE
B, OscA running
OscB running and selected +
OscA running
XX
0
X
INVALID
OscA & OscB cannot be stopped
at the same time
XX
X
0
1
INVALID
OscA must not be stopped, as
used for CPU and peripherals
XX
0
X
0
INVALID
OscB must not be stopped as
used for CPU and peripherals
0
1
X
1
IDLE MODE A
The CPU is off, OscA supplies the
peripherals, OscB can be disabled
(OscBEn = 0)
相关PDF资料
PDF描述
AT91SAM7X128B-CU IC MCU 128KB FLASH 100TFBGA
AT91SAM7XC128B-AU MCU ARM 128K HS FLASH 100-LQFP
ATSAM3U1CA-CU IC MCU 32BIT 64KB FLASH 100TFBGA
1981584-1 CONN RCPT MICRO USB TYPE AB
1981568-1 CONN RCPT MICRO USB B R/A SMD
相关代理商/技术参数
参数描述
AT89C51ID2-SMSIM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2-UM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51RB2 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/ 32K Bytes Flash
AT89C51RB2/RC2 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT89C51RB2/RC2 [Updated 4/03. 125 Pages]
AT89C51RB2_06 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/ 32K Bytes Flash