- 您现在的位置：买卖IC网 > Datasheet目录395 > ATAKSTK511-3 (Atmel)KIT RF MODULE 315MHZ FOR STK500 Datasheet资料下载
参数资料
| 型号： | ATAKSTK511-3 |
| 厂商： | Atmel |
| 文件页数： | 18/37页 |
| 文件大小： | 0K |
| 描述： | KIT RF MODULE 315MHZ FOR STK500 |
| 标准包装： | 1 |
| 系列： | SmartRF® |
| 类型： | 发射器，接收器，ASK，FSK |
| 频率： | 433MHz |
| 适用于相关产品： | ATSTK500-ND |
| 已供物品： | 3 个板，天线，CD |
| 产品目录页面： | 553 (CN2011-ZH PDF) |
| 其它名称： | Q2262874 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
STK511 Receiver Interface Board
The following table shows how the signals from the receiver connectors (U2) are routed to the microcon-
troller I/O ports. As shipped, the STK511 Receiver Interface Board routes the Receiver Application
Board signals, necessary for stand-alone operation, to the on-board microcontroller. The remaining sig-
nals are routed to the STK500 through the expansion connectors. See section “Receive Signal Routing”
on page 4-6 for additional information.
Receiver Signal to I/O Port Mapping
U2 Connector
Receiver Application Board
Microcontroller I/O
Pin #
12
11
10
9
8
7
6
5
4
3
2
1
ATA5743
VCC
GND
DATA
---
---
MODE
D_CLK
SENS
IC_Active
POL/ON
---
---
ATA5760/1
VCC
GND
DATA
---
---
V DIV
D_CLK
SENS
IC_ACTIVE
POL/ON
---
---
ATA5744
VCC
GND
DATA
---
BR0
BR1
RSSI
---
---
ENABLE
---
---
Port
---
---
PB4
---
PB1
PB3
PB2
---
PB1
PB0
---
---
4.2.2
Configuration Register DIP Switches
Upon receiving power, the receiver’s OPMODE and LIMIT registers contain default settings. Any values
other than the default require programming. The OPMODE register controls Baud Rate range, Bit Check
quantity, Modulation type, Sleep polling time, and Noise Suppression. The LIMIT register controls the
maximum and minimum valid time between edges. See the receiver datasheet for more information on
the registers.
The DIP switches on the STK511 Receiver Interface Board allow individual bits in these registers to be
modified. As an added convenience, the STK511 Receiver Interface Board contains a silkscreen legend
that specifies each bit function for both registers as well as their corresponding default value.
The configuration register DIP switches connect to the following I/O ports of the ATmega8515 AVR
microcontroller which is integral to the STK511 Receiver Interface Board. The bits not listed in the table
below are set to constants in the firmware.
Table 4-1. DIP Switch to I/O Port Mapping
OPMODE Register
Bit1
---
Bit2
---
Bit3
PD0
Bit4
PD1
Bit5
PD2
Bit6
PD3
Bit7
PD4
Bit8
PD5
Bit9
PD6
Bit10
PD7
Bit11
PC0
Bit12
PC1
Bit13
PC2
Bit14
PC3
Bit15
---
LIMIT Register
Bit1
---
Bit2
---
Bit3
PA0
Bit4
PA1
Bit5
PA2
Bit6
PA3
Bit7
PA4
Bit8
PA5
Bit9
PA6
Bit10
PA7
Bit11
PC4
Bit12
PC5
Bit13
PC6
Bit14
PC7
Bit15
---
4-4
4842B–AVR–10/09
STK511 User Guide
相关PDF资料 |
PDF描述 |
|---|---|
| ATAKSTK512-3 | KIT RF MOD REMOTE 315MHZ UNIDIR |
| ATAVRUSBRF01 | KIT REF DES AVR NORDIC 2.4GHZ |
| ATMEGA128RFA1-ZUR | IC AVR MCU 2.4GHZ XCEIVER 64QFN |
| ATMEGA64RZAPV-10AU | BUNDLE ATMEGA644P/AT86RF230 TQFP |
| ATP101-TL-H | MOSFET P-CH 30V 25A ATPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATAKSTK511-4 | 功能描述:射频开发工具 434 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-8 | 功能描述:射频开发工具 868 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-9 | 功能描述:射频开发工具 915 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-3 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-4 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。