- 您现在的位置：买卖IC网 > Datasheet目录395 > ATAKSTK511-3 (Atmel)KIT RF MODULE 315MHZ FOR STK500 Datasheet资料下载
参数资料
| 型号： | ATAKSTK511-3 |
| 厂商： | Atmel |
| 文件页数： | 36/37页 |
| 文件大小： | 0K |
| 描述： | KIT RF MODULE 315MHZ FOR STK500 |
| 标准包装： | 1 |
| 系列： | SmartRF® |
| 类型： | 发射器，接收器，ASK，FSK |
| 频率： | 433MHz |
| 适用于相关产品： | ATSTK500-ND |
| 已供物品： | 3 个板，天线，CD |
| 产品目录页面： | 553 (CN2011-ZH PDF) |
| 其它名称： | Q2262874 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页
Troubleshooting Guide
Table 7-1. Troubleshooting Solutions (Continued)
Problem
Transmitter Application Board
LED(s) constantly lit
Unable to program Transmitter
Application board through ISP
header
Demo not working (STK500 LED(s)
not responding to transmitted
signal)
Reason
Demo Software corrupted
Incorrect orientation of the ribbon
cable connecting the ISP header to
the STK500
Power not supplied to transmitter
on-board microcontroller
Wrong device selected in the
STK500 software
Power and serial cable not
connected to STK500
Incorrect orientations of the
Receiver Application Board or
Receiver Interface Board
Power not properly supplied to all
boards
Data Selector switch not set to
STK500 position
Microcontroller socket on STK500
not populated
Corrupted software in the STK500
microcontroller
10-pin ribbon cable not connected
properly
Incompatible modulation used on
the transmitter and receiver
CdS Photocell covered
Solution
Reload the desired software
according to section “Software
Description” on page 4-6
Verify the orientation of both sides
of the ribbon cable
Supply 3 volts to the transmitter
microcontroller through the coin cell
battery or via the STK500
Select ATtiny13 from the Device
menu. Verify that the signature byte
matches in the Advanced tab
Verify setup of the STK500
hardware
Verify the hardware is assembled
correctly as shown in chapter 1
See troubleshooting section for
each board.
Set the switch to the proper position
and re-run the demo
The demo uses an AT90S8515
microcontroller in the STK500 to
decode the received signal
Reload the Receiver Decode
software as shown in Figure 2-1
on page 2-2
Verify that the 10-pin ribbon cable is
properly connected to the LEDS
header from the PORTC header on
the STK500
Verify that transmitter and receiver
are both set for the same
modulation type (ASK versus FSK)
The LED(s) on the STK500 are only
active when the CdS Photocell is
subjected to a light source and one
of the buttons has been pressed
STK511 User Guide
Receiver set to permanent sleep
Receiver limits incorrect
Receiver antenna not connected
Check for Sleep bits in the
OPMODE register set for all 1
Verify correct register settings as
given in chapter 1
Connect external whip antenna to
Receiver Application Board
7-3
4842B–AVR–10/09
相关PDF资料 |
PDF描述 |
|---|---|
| ATAKSTK512-3 | KIT RF MOD REMOTE 315MHZ UNIDIR |
| ATAVRUSBRF01 | KIT REF DES AVR NORDIC 2.4GHZ |
| ATMEGA128RFA1-ZUR | IC AVR MCU 2.4GHZ XCEIVER 64QFN |
| ATMEGA64RZAPV-10AU | BUNDLE ATMEGA644P/AT86RF230 TQFP |
| ATP101-TL-H | MOSFET P-CH 30V 25A ATPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATAKSTK511-4 | 功能描述:射频开发工具 434 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-8 | 功能描述:射频开发工具 868 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-9 | 功能描述:射频开发工具 915 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-3 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-4 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。