- 您现在的位置：买卖IC网 > Datasheet目录395 > ATAKSTK511-3 (Atmel)KIT RF MODULE 315MHZ FOR STK500 Datasheet资料下载
参数资料
| 型号： | ATAKSTK511-3 |
| 厂商： | Atmel |
| 文件页数： | 19/37页 |
| 文件大小： | 0K |
| 描述： | KIT RF MODULE 315MHZ FOR STK500 |
| 标准包装： | 1 |
| 系列： | SmartRF® |
| 类型： | 发射器，接收器，ASK，FSK |
| 频率： | 433MHz |
| 适用于相关产品： | ATSTK500-ND |
| 已供物品： | 3 个板，天线，CD |
| 产品目录页面： | 553 (CN2011-ZH PDF) |
| 其它名称： | Q2262874 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
STK511 Receiver Interface Board
4.2.3
4.2.4
Configuration Register LED Indicators
Each configuration register bit has a corresponding LED on the STK511 Receiver Interface Board and is
grouped according to specific functions. If an LED is ON the corresponding bit is set to logic 1 . The LEDs
are enclosed by the silkscreen legend and become part of the table for easy reference.
DATA Selector Switch
The DATA selector switch controls the routing of the bi-directional DATA line coming from the Receiver
Application Board. The switch either routes the DATA line to the STK511 Receiver Interface Board's on-
board microcontroller or to the Atmel AVR microcontroller on the STK500 board. The silkscreen legend
designates the selected mode based on switch position. To enable the Receiver Application Board, a
low pulse must be applied to the DATA line whenever power is applied (see receiver datasheet “Clearing
the Reset Marker” for more detail). The STK511 Receiver Interface Board provides this signal as part of
the firmware initialization routine. Therefore, when powering up the STK511 Starter Kit and configuring
the registers in the receiver, the DATA Selector Switch must be set to the STK511 position.
Note:
This is probably the single most important piece of information regarding the successful operation of this
Evaluation Kit. Having this switch in the wrong position can cause a lot of unexplained problems. Always
verify that this switch is set to desired position.
4.2.5
Configure Push Button
The configuration selected by the DIP switches is not programmed into the receiver until the Configure
button is pressed. When pressed, the on-board microcontroller programs these values into the appropri-
ate registers of the receiver. Each register is written twice to allow verification that the proper data was
set. The button is connected to PB6 of the on-board microcontroller I/O port.
Note:
The Data selector switch must first be set to the STK511 position for the settings to be written into the
receiver.
4.2.6
On-board Microcontroller
The STK511 Receiver Interface Board’s on-board microcontroller is the ATmega8515 8-bit AVR. It is
shipped with all of the firmware for supporting the functions of the STK511 Starter Kit. Programming the
flash memory of this microcontroller can be achieved through the STK500.
In order to reprogram the on-board microcontroller through the STK500 complete the following steps:
1. All devices must be removed from the programming sockets on the STK500.
2. Short the ISP Jumper (JP2) on the STK511 Receiver Interface Board.
3. The SPROG3 header on the STK500 must be connected to the ISP6PIN header.
4. The STK511 Receiver Interface Board must be connected through the expansion connectors
(EXPAND0 and EXPAND1).
The ISP pins are connected to the following I/O pins on the microcontroller.
Table 4-2. STK511 Receiver Interface Board On-board Programming Pinout
STK511 User Guide
ISP Pin
PB7
PB6
PB5
RST
I/O Pin Microcontroller
SCK
MOSI
MISO
RST
4-5
4842B–AVR–10/09
相关PDF资料 |
PDF描述 |
|---|---|
| ATAKSTK512-3 | KIT RF MOD REMOTE 315MHZ UNIDIR |
| ATAVRUSBRF01 | KIT REF DES AVR NORDIC 2.4GHZ |
| ATMEGA128RFA1-ZUR | IC AVR MCU 2.4GHZ XCEIVER 64QFN |
| ATMEGA64RZAPV-10AU | BUNDLE ATMEGA644P/AT86RF230 TQFP |
| ATP101-TL-H | MOSFET P-CH 30V 25A ATPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATAKSTK511-4 | 功能描述:射频开发工具 434 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-8 | 功能描述:射频开发工具 868 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-9 | 功能描述:射频开发工具 915 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-3 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-4 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。