- 您现在的位置：买卖IC网 > Datasheet目录395 > ATAKSTK511-3 (Atmel)KIT RF MODULE 315MHZ FOR STK500 Datasheet资料下载
参数资料
| 型号： | ATAKSTK511-3 |
| 厂商： | Atmel |
| 文件页数： | 7/37页 |
| 文件大小： | 0K |
| 描述： | KIT RF MODULE 315MHZ FOR STK500 |
| 标准包装： | 1 |
| 系列： | SmartRF® |
| 类型： | 发射器，接收器，ASK，FSK |
| 频率： | 433MHz |
| 适用于相关产品： | ATSTK500-ND |
| 已供物品： | 3 个板，天线，CD |
| 产品目录页面： | 553 (CN2011-ZH PDF) |
| 其它名称： | Q2262874 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
Getting Started
1. Once the hardware is setup, verify that the DATA selector switch is in the STK511 position.
2. Apply power, locate the DIP switch corresponding to the OPMODE register, and set the 5th DIP
switch to the ON position. The LED enclosed in the silkscreen legend labeled Mod should light up,
indicating a 1 (corresponding to ASK mode) was selected.
3. Press the Configure button to program the OPMODE and LIMIT registers with the selected
configuration.
Now, the receiver is ready to receive an ASK (or in most cases, On-Off Keyed - OOK) signal. The
demodulated signal appears on the DATA line of the Receiver Application Board. This signal can be
routed to the on-board microcontroller or to the STK500, depending on the position of the DATA selector
switch and values of jumpers R25-R32 ( See “Receive Signal Routing ” on page 4-6. for additional
information).
2.3
2.3.1
Running the Demo
The Transmitter Application Board contained in the evaluation kit is shipped preprogrammed with a light
intensity sensor program. It can be used with the STK500/511 Assembly to display ambient light inten-
sity using LEDs on the STK500. To run this demo it must first be properly configured.
STK500 Configuration
1. Insert an AT90S8515 microcontroller into the red 40-pin socket (SCKT3000D3) on the STK500
board.
2. Verify that the 6-pin ribbon cable is connected between the SPROG3 and the ISP6PIN headers and
is oriented correctly.
3. Connect the 10-pin ribbon cable from the LEDS header to the PORTC header.
4. Apply power (12 V) to the supplied connector and turn on the STK500 power switch.
5. Connect the serial cable between RS232 CTRL and the host PC.
6. In AVR Studio, select Tools/STK500 from the menu.
7. Select the Board tab and verify that the VTARGET voltage is set to 5 V.
8. On the Program tab , select AT90S8515 from the Device pull-down menu.
9. Load the STK511 RX Decode.hex file, included on the Sample Software CD, into the field labeled
Flash Input Hex File and press the Program button (see Figure 2-1 on page 2-2 ).
2-2
4842B–AVR–10/09
Figure 2-1.
Receiver Decode Software
STK511 User Guide
相关PDF资料 |
PDF描述 |
|---|---|
| ATAKSTK512-3 | KIT RF MOD REMOTE 315MHZ UNIDIR |
| ATAVRUSBRF01 | KIT REF DES AVR NORDIC 2.4GHZ |
| ATMEGA128RFA1-ZUR | IC AVR MCU 2.4GHZ XCEIVER 64QFN |
| ATMEGA64RZAPV-10AU | BUNDLE ATMEGA644P/AT86RF230 TQFP |
| ATP101-TL-H | MOSFET P-CH 30V 25A ATPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATAKSTK511-4 | 功能描述:射频开发工具 434 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-8 | 功能描述:射频开发工具 868 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-9 | 功能描述:射频开发工具 915 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-3 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-4 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。