- 您现在的位置：买卖IC网 > Datasheet目录395 > ATAKSTK511-3 (Atmel)KIT RF MODULE 315MHZ FOR STK500 Datasheet资料下载
参数资料
| 型号： | ATAKSTK511-3 |
| 厂商： | Atmel |
| 文件页数： | 6/37页 |
| 文件大小： | 0K |
| 描述： | KIT RF MODULE 315MHZ FOR STK500 |
| 标准包装： | 1 |
| 系列： | SmartRF® |
| 类型： | 发射器，接收器，ASK，FSK |
| 频率： | 433MHz |
| 适用于相关产品： | ATSTK500-ND |
| 已供物品： | 3 个板，天线，CD |
| 产品目录页面： | 553 (CN2011-ZH PDF) |
| 其它名称： | Q2262874 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
Section 2
Getting Started
The STK ? 511 Starter Kit comes complete with all the hardware needed to demonstrate a working RF
system. Included are the STK511Interface Board, RF Receiver Application Board, and RF Transmitter
Application Board.
2.1
2.2
Setting up the Hardware
The Receiver Application Board should be oriented with its signal pins toward the DIP switches and
LEDs on the STK511 Receiver Interface Board. This places the power and ground test points on the top
of the receiver board adjacent to the DATA selector switch. Insert the receiver board into the provided
connectors.
If the STK511 Receiver Interface Board is used as an expansion card for the STK500, align the
EXPAND0 and EXPAND1 connectors with the corresponding EXPAND0 and EXPAND1 headers on the
STK500 and press together. Be cautious of pinching any ribbon cable ends on the STK500 board when
inserting the STK511 Receiver Interface Board into the connectors.
Once the Receiver Application Board has been inserted into both twelve-pin connectors, power must be
supplied in one of two ways:
A) the power and ground pins on the Receiver Application Board can be connected to a +5V supply, or
B) the supply can be sourced through the STK500 connectors EXPAND0 and EXPAND1.
If the STK500 is used to source power, the VTARGET jumper (located on the STK500) must be con-
nected and VTARGET set to 5V in the STK500 board settings located under the appropriate tab in AVR
Studio ? , Atmel's software development tool.
Configuring the Receiver
Atmel RF Receivers designated ATA5743, ATA5760 and ATA5761 contain two configuration registers
(Atmel RF receiver designated ATA5744 does not). These registers control the digital processing of the
incoming RF signal, as well as define the receivers’ polling interval. The register values are stored in vol-
atile memory and are lost when power is removed; therefore, they must be re-programmed every time
power is applied. Programming is achieved with a one-wire protocol using the receivers’ DATA line. This
line is bi-directional and is also used for providing the demodulated data to the user. More detail on this
can be found in the individual receivers’ datasheets.
With this in mind, the user must decide how to configure the receiver for the intended application. To
illustrate this process, the following example will show how to change the receiver to ASK from its default
mode of FSK.
STK511 User Guide
2-1
4842B–AVR–10/09
相关PDF资料 |
PDF描述 |
|---|---|
| ATAKSTK512-3 | KIT RF MOD REMOTE 315MHZ UNIDIR |
| ATAVRUSBRF01 | KIT REF DES AVR NORDIC 2.4GHZ |
| ATMEGA128RFA1-ZUR | IC AVR MCU 2.4GHZ XCEIVER 64QFN |
| ATMEGA64RZAPV-10AU | BUNDLE ATMEGA644P/AT86RF230 TQFP |
| ATP101-TL-H | MOSFET P-CH 30V 25A ATPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATAKSTK511-4 | 功能描述:射频开发工具 434 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-8 | 功能描述:射频开发工具 868 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-9 | 功能描述:射频开发工具 915 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-3 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-4 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。