- 您现在的位置：买卖IC网 > Datasheet目录395 > ATAKSTK511-3 (Atmel)KIT RF MODULE 315MHZ FOR STK500 Datasheet资料下载
参数资料
| 型号： | ATAKSTK511-3 |
| 厂商： | Atmel |
| 文件页数： | 35/37页 |
| 文件大小： | 0K |
| 描述： | KIT RF MODULE 315MHZ FOR STK500 |
| 标准包装： | 1 |
| 系列： | SmartRF® |
| 类型： | 发射器，接收器，ASK，FSK |
| 频率： | 433MHz |
| 适用于相关产品： | ATSTK500-ND |
| 已供物品： | 3 个板，天线，CD |
| 产品目录页面： | 553 (CN2011-ZH PDF) |
| 其它名称： | Q2262874 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页
Troubleshooting Guide
Table 7-1. Troubleshooting Solutions (Continued)
Problem
Registers in the receiver do not
appear to be programming
Unable to load Receiver Interface
Board firmware
Transmitter not responding to
button press
No activity on Transmitter
Reason
Power supplied is too low
DATA Selector switch was not set to
the STK511 position when
Configure button pressed
Receiver Interface Board firmware
has become corrupted
Registers may be programming
correctly with no visible signs of
change
Some external source may be
holding the Data line low
Receiver Application Board rotated
180° when mounted on the
Receiver Interface Board
Receiver Interface Board not
correctly connected to STK500
ISP ribbon cable not connected
properly
Incorrect device selected
Device present in STK500 sockets
ISP jumper not shorted on Receiver
Interface Board
Power and serial cable not
connected to STK500
Battery dead
Demo Software corrupted
Switch contact not made
Low Battery voltage
Transmitter is in sleep mode
Solution
Verify that the power being supplied
is 5V
Set DATA Selector switch to
STK511 and re-press button
Reload the Receiver Interface
Board Firmware as described in
section “Software Description”
on page 3-3
Monitor the Data Testpoint with an
oscilloscope to check for presence
of the acknowledge bit
Verify that Receiver Application
Board signal testpoints are toward
the DIP switches.
Verify EXPAND0 and EXPAND1 are
properly oriented
Ensure ribbon cable connected
between ISP6PIN header and
SPROG3 header
Check orientation of pin 1 on
headers
Select ATmega8515 from the
Device menu. Verify that the
signature byte matches in the
Advanced tab
Remove all devices from the
programming sockets of the
STK500
Connect shunt
Verify setup of the STK500
hardware
Open Transmitter Application Board
case and replace coin cell battery
Reload the desired software
according to section “Software
Description” on page 4-6
Ensure proper contact of the button
to the Transmitter Application Board
Replace coin cell battery
Press button to wake from sleep
mode
7-2
4842B–AVR–10/09
Application Board LED(s)
Demo Software corrupted
Reload the desired software
according to section “Software
Description” on page 4-6
STK511 User Guide
相关PDF资料 |
PDF描述 |
|---|---|
| ATAKSTK512-3 | KIT RF MOD REMOTE 315MHZ UNIDIR |
| ATAVRUSBRF01 | KIT REF DES AVR NORDIC 2.4GHZ |
| ATMEGA128RFA1-ZUR | IC AVR MCU 2.4GHZ XCEIVER 64QFN |
| ATMEGA64RZAPV-10AU | BUNDLE ATMEGA644P/AT86RF230 TQFP |
| ATP101-TL-H | MOSFET P-CH 30V 25A ATPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATAKSTK511-4 | 功能描述:射频开发工具 434 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-8 | 功能描述:射频开发工具 868 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK511-9 | 功能描述:射频开发工具 915 MHz AVR based RF Starterkit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-3 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| ATAKSTK512-4 | 功能描述:射频开发工具 REMOTE ACCESS CNTRL UNDIRECTIONAL KIT RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。