参数资料
型号: ATAM893T-TKQ
厂商: Atmel
文件页数: 62/98页
文件大小: 0K
描述: IC MON TIRE-PRESS ATARX9X SER
标准包装: 4,000
系列: MARC4
核心处理器: MARC4
芯体尺寸: 4-位
速度: 4MHz
连通性: SSI(2 线,3 线)
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 16
程序存储器容量: 4KB(4K x 8)
程序存储器类型: EEPROM
EEPROM 大小: 64 x 16
RAM 容量: 256 x 4
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 6.5 V
振荡器型: 内部
工作温度: -40°C ~ 125°C
封装/外壳: 20-SOIC(0.209",5.30mm 宽)
包装: 带卷 (TR)
65
4680C–4BMCU–01/05
ATAM893-D
5.3.4.5
9-bit Shift Mode
In the 9-bit shift mode, the SSI is able to handle the MCL protocol (described below). It always
operates as an MCL master device, i.e., SC is always generated and output by the SSI. Both the
MCL start and stop conditions are automatically generated whenever the SSI is activated or
deactivated by the SIR bit. In accordance with the MCL protocol, the output data is always
changed in the clock low phase and shifted in on the high phase.
Before activating the SSI (SIR = 0) and commencing an MCL dialog, the appropriate data direc-
tion for the first word must be set using the SDD control bit. The state of this bit controls the
direction of the data port (BP43 or MCL_SD). Once started, the 8 data bits are, depending on
the selected direction, either clocked into or out of the shift register. During the 9th clock period,
the port direction is automatically switched over so that the corresponding acknowledge bit can
be shifted out or read in. In transmit mode, the acknowledge bit received from the slave device is
captured in the SSI Status Register (TACK) where it can be read by the controller. In receive
mode, the state of the acknowledge bit to be returned to the slave device is predetermined by
the SSI Status Register (RACK).
Changing the directional mode (TX/RX) should not be performed during the transfer of an MCL
telegram. One should wait until the end of the telegram which can be detected using the SSI
interrupt (IFN = 1) or by interrogating the ACT status.
Once started, a 9-bit telegram will always run to completion and will not be prematurely termi-
nated by the SIR bit. So, if the SIR bit is set to ‘1’ in telegram, the SSI will complete the current
transfer and terminate the dialog with an MCL stop condition.
Figure 5-42. Example of MCL Transmit Dialog
7 6 5 432 1
7 6 5 43 210 A
msb
lsb
tx data 1
tx data 2
msb
lsb
Write STB
(tx data 1)
SC
SD
SRDY
ACT
Interrupt
(IFN = 0)
Interrupt
(IFN = 1)
0A
Write STB
(tx data 2)
SIR
SDD
Start
Stop
相关PDF资料
PDF描述
TSC80251G2D-L16CER IC MCU 8BIT 16MHZ LO VOLT 44VQFP
TSC87251G2D-L16CER IC MCU 8BIT 32K OTP 16MHZ 44VQFP
PIC18F86K90-I/PTRSL MCU PIC 64K FLASH XLP 80TQFP
201692-4 CONN HOUSING PLUG 104POS BLACK
202800-2 CONN HOUSING RECEPT 160POS BLACK
相关代理商/技术参数
参数描述
ATAM893T-TKQYD 功能描述:4位微控制器 - MCU Marc4 micrium 4 k FLASH RoHS:否 最大时钟频率:32 KHz/4 MHz 程序存储器大小:4 KB 封装 / 箱体:SSO-20 制造商:Atmel 核心:MARC4 数据总线宽度:4 bit 安装风格:SMD/SMT
ATAM893T-TKS 功能描述:IC MON TIRE-PRESS ATARX9X SER RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:MARC4 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C,LIN,SPI,UART/USART,USI 外围设备:欠压检测/复位,POR,PWM,温度传感器,WDT 输入/输出数:16 程序存储器容量:8KB(4K x 16) 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC(0.295",7.50mm 宽) 包装:带卷 (TR)
ATAM893T-TKSYD 功能描述:4位微控制器 - MCU Marc4 micrium 4k FLASH RoHS:否 最大时钟频率:32 KHz/4 MHz 程序存储器大小:4 KB 封装 / 箱体:SSO-20 制造商:Atmel 核心:MARC4 数据总线宽度:4 bit 安装风格:SMD/SMT
ATAM893X-TKHYZ 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Flash Version for ATAR080, ATAR090/890 and ATAR092/892
ATAM893X-TKQYZ 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Flash Version for ATAR080, ATAR090/890 and ATAR092/892