- 您现在的位置：买卖IC网 > Datasheet目录316 > BU9883FV-WE2 (Rohm Semiconductor)IC EEPROM 6KBIT 400KHZ SSOP16 Datasheet资料下载
参数资料
| 型号： | BU9883FV-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 20/28页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 6KBIT 400KHZ SSOP16 |
| 标准包装： | 2,500 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 6K（256 x 8 x 3） |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-SSOPB |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
BU9883FV-W
Datasheet
● Command cancel by start condition and stop condition
During command input, by continuously inputting start condition and stop condition, command can be cancelled.
(Refer to Figure 49.)
However, in ACK output area and during data read, SDA0 to 3 buses may output 'L', and in this case, start condition and
stop condition cannot be input, so reset is not available. Therefore, execute software reset. And when command is
cancelled by start, stop condition, during random read cycle, sequential read cycle, or current read cycle, internal setting
address is not determined, therefore, it is not possible to carry out current read cycle in succession. When to carry out read
cycle in accession, carry out random read cycle.
SCL0 to 3
SDA0 to 3
1
0
1
0
Start condition
Stop condition
Figure 49. Case of cancel by start, stop condition during slave address input
● I/O peripheral circuit
○ Pull up resistance of SDA0 to 3 terminal
SDA0 to 3 is NMOS open drain, so requires pull up resistance. As for this resistance value (R PU ), select an appropriate
value to this resistance value from microcontroller V IL , I L , and V OL 0 to 3-I OL characteristics of this IC. If R PU is large,
action frequency is limited. The smaller the R PU , the larger the consumption current at action.
○ Maximum value of R PU
The maximum value of R PU is determined by the following factors. The following V CC , SDA, R PU and I L correspond to
them of each port.
(1)SDA0 to 3 rise time to be determined by the capacitance (CBUS) of bus line of R PU and SDA0 to 3 should be tR or
below.
And AC timing should be satisfied even when SDA0 to 3 rise time is late.
(2)The bus electric potential
A
to be determined by input leak total (I L ) of device connected to bus at output of 'H' to
SDA0 to 3 bus and R PU should sufficiently secure the input 'H' level (V IH ) of microcontroller and EEPROM including
recommended noise margin 0.2V CC .
Vcc - I L R PU － 0.2Vcc ≧ V IH
Microcontroller
BU9883FV-W
∴
R PU ≦
0.8Vcc － V IH
I L
R PU
A
SDA terminal
Ex. ) When V CC =3V, I L =10 μ A, V IH =0.7 V CC ,
from (2)
IL
IL
Bus line
10 × 10
R PU ≦
0.8 × 3 － 0.7 × 3
-6
capacity
CBUS
≦ 300 [k Ω ]
Figure 50. I/O circuit diagram
○ Minimum value of R PU
The minimum value of R PU is determined by the following factors. The following V CC , V OL , I OL , and R PU correspond to
them of each port.
(1)When IC outputs LOW, it should be satisfied that V OLMAX =0.4V and I OLMAX =3mA.
V CC － V OL
R PU
≦ I OL
∴
R PU ≦
Vcc － V OL
I OL
(2)V OLMAX =0.4V should secure the input 'L' level (V IL ) of microcontroller and EEPROM including recommended noise
margin 0.1V CC .
V OLMAX ≦ V IL - 0.1 V CC
Ex. ) When V CC =3V, V OL =0.4V, I OL =3mA, microcontroller, EEPROM V IL =0.3V CC
from (1)
R PU ≧
≧
3 － 0.4
3 × 10
867 [ Ω ]
-3
And
V OL = 0.4 [V]
V IL = 0.3 × 3
= 0.9 [V]
○ Pull up resistance of SCL0 to 3 terminal
Therefore, the condition (2) is satisfied.
When SCL0 to 3 control is made at CMOS output port, there is no need, but in the case there is timing where SCL0 to 3
becomes 'Hi-Z', add a pull up resistance. As for the pull up resistance, one of several k ? to several ten k ? is
recommended in consideration of drive performance of output port of microcontroller.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
20/25
TSZ02201-0R2R0G100420-1-2
31.AUG.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BU9889GUL-WE2 | IC EEPROM 8KBIT 2WIRE VCSP50L1 |
| BU9891GUL-WE2 | IC EEPROM 4KBIT VCSP T/R |
| BU9897GUL-WE2 | IC EEPROM SERIAL VCSP50L2 |
| BU99901GUZ-WE2 | IC EEPROM 32KBIT 2WIRE VCSP |
| BUK218-50DY,118 | TOPFET DUAL SWITCH D2PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BU9888FV-W | 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs |
| BU9888FV-WE2 | 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs |
| BU9889GUL-W | 制造商:ROHM 制造商全称:Rohm 功能描述:WL-CSP EEPROM family I2C BUS |
| BU9889GUL-WE2 | 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器 Serial-2Wire 8Kb RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BU9890GUL-W | 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit |
发布紧急采购，3分钟左右您将得到回复。