- 您现在的位置：买卖IC网 > PDF目录11783 > DS1875T+ (Maxim Integrated Products)IC SFP CTRLR/TRIPLEXER 38-TQFN PDF资料下载
参数资料
| 型号： | DS1875T+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/92页 |
| 文件大小： | 0K |
| 描述： | IC SFP CTRLR/TRIPLEXER 38-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 应用： | 光纤 |
| 接口： | I²C |
| 电源电压： | 2.85 V ~ 3.9 V |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-TQFN（5x7） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1431 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
DS1875
Die Identification
The DS1875 has an ID hard-coded to its die. Two regis-
ters (Table 02h, Registers 86h–87h) are assigned for
this feature. Byte 86h reads 75h to identify the part as
the DS1875; byte 87h reads the die revision.
Low-Voltage Operation
The DS1875 contains two power-on reset (POR) levels.
The lower level is a digital POR (VPOD) and the higher
level is an analog POR (VPOA). At startup, before the
supply voltage rises above VPOA, the outputs are dis-
abled (FETG and BIAS outputs are high impedance,
MOD is low), all SRAM locations are low (including
shadowed EEPROM (SEE)), and all analog circuitry is
disabled. When VCC reaches VPOA, the SEE is
recalled, and the analog circuitry is enabled. While VCC
remains above VPOA, the device is in its normal operat-
ing state, and it responds based on its nonvolatile con-
figuration. If during operation VCC falls below VPOA but
is still above VPOD, the SRAM retains the SEE settings
from the first SEE recall, but the device analog is shut
down and the outputs are disabled. FETG is driven to
its alarm state defined by the FETG DIR bit (Table 02h,
Register 89h). If the supply voltage recovers back
above VPOA, the device immediately resumes normal
functioning. When the supply voltage falls below VPOD,
the device SRAM is placed in its default state and
another SEE recall is required to reload the nonvolatile
settings. The EEPROM recall occurs the next time VCC
exceeds VPOA. Figure 9 shows the sequence of events
as the voltage varies.
Any time VCC is above VPOD, the I2C interface can be
used to determine if VCC is below the VPOA level. This
is accomplished by checking the RDYB bit in the status
(Lower Memory, Register 6Eh) byte. RDYB is set when
VCC is below VPOA. When VCC rises above VPOA,
RDYB is timed (within 500s) to go to 0, at which point
the part is fully functional.
For all device addresses sourced from EEPROM (Table
02h, Register 8Ch), the default device address is A2h
until VCC exceeds VPOA, allowing the device address
to be recalled from the EEPROM.
Enhanced RSSI Monitoring (Dual Range
Functionality)
The DS1875 offers a new feature to improve the accu-
racy and range of MON3, which is most commonly
used for monitoring RSSI. This feature enables right-
shifting (along with its gain and offset settings) when
the input signal is below a set threshold (within the
range that benefits using right-shifting) and then auto-
matically disables right-shifting (recalling different gain
and offset settings) when the input signal exceeds the
threshold. Also, to prevent “chattering,” hysteresis pre-
vents excessive switching between modes in addition
to ensuring that continuity is maintained. Dual range
operation is enabled by default (factory programmed in
EEPROM). However, it can easily be disabled through
the RSSI_FF and RSSI_FC bits. When dual range oper-
ation is disabled, MON3 operates identically to the
other MON channels, although featuring a differential
input.
VCC
VPOA
VPOD
FETG
SEE
HIGH
IMPEDANCE
HIGH
IMPEDANCE
HIGH
IMPEDANCE
NORMAL
OPERATION
DRIVEN TO
FETG DIR
NORMAL
OPERATION
PRECHARGED
TO 0
PRECHARGED
TO 0
PRECHARGED
TO 0
RECALLED
VALUE
RECALLED
VALUE
DRIVEN TO
FETG DIR
NORMAL
OPERATION
DRIVEN TO
FETG DIR
SEE RECALL
Figure 9. SEE Timing
PON Triplexer and SFP Controller
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20MD18PA | CONN RCPT 18POS WALL MNT W/PINS |
| MAX7359ETG+ | IC KEY SWITCH 2WIRE 24-TQFN |
| USB-232-SS | IC USB ASYNC SRL UART 20-SSOP |
| MS27473E24F61P | CONN PLUG 61POS STRAIGHT W/PINS |
| MS27474E10F98PA | CONN RCPT 6POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1875T+ | 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1875T+T&R | 制造商:Maxim Integrated Products 功能描述:PON TRIPLEXER 38TQFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SFP CTRLR/TRIPLEXER 38-TQFN 制造商:Maxim Integrated Products 功能描述:ADC / DAC Multichannel PON Triplexer & SFP Controller |
| DS1875T+T&R | 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1875T+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer and SFP Controller |
| DS1876 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SFP Controller with Dual LDD Interface |
发布紧急采购，3分钟左右您将得到回复。