- 您现在的位置：买卖IC网 > PDF目录11783 > DS1875T+ (Maxim Integrated Products)IC SFP CTRLR/TRIPLEXER 38-TQFN PDF资料下载
参数资料
| 型号： | DS1875T+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 22/92页 |
| 文件大小： | 0K |
| 描述： | IC SFP CTRLR/TRIPLEXER 38-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 应用： | 光纤 |
| 接口： | I²C |
| 电源电压： | 2.85 V ~ 3.9 V |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-TQFN（5x7） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1431 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
DS1875
SCL
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
SDA
STOP
START
REPEATED
START
tBUF
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
tHD:STA
tSP
tSU:STA
tHIGH
tR
tF
tLOW
Figure 15. I2C Timing Diagram
I2C Communication
I2C Definitions
The following terminology is commonly used to
describe I2C data transfers.
Master Device: The master device controls the
slave devices on the bus. The master device gener-
ates SCL clock pulses and START and STOP condi-
tions.
Slave Devices: Slave devices send and receive
data at the master’s request.
Bus Idle or Not Busy: Time between STOP and
START conditions when both SDA and SCL are inac-
tive and in their logic-high states.
START Condition: A START condition is generated
by the master to initiate a new data transfer with a
slave. Transitioning SDA from high to low while SCL
remains high generates a START condition. See
Figure 15 for applicable timing.
STOP Condition: A STOP condition is generated by
the master to end a data transfer with a slave.
Transitioning SDA from low to high while SCL
remains high generates a STOP condition. See
Figure 15 for applicable timing.
Repeated START Condition: The master can use a
repeated START condition at the end of one data
transfer to indicate that it will immediately initiate a
new data transfer following the current one.
Repeated START conditions are commonly used
during read operations to identify a specific memory
address to begin a data transfer. A repeated START
condition is issued identically to a normal START
condition. See Figure 15 for applicable timing.
Bit Write: Transitions of SDA must occur during the
low state of SCL. The data on SDA must remain valid
and unchanged during the entire high pulse of SCL
plus the setup and hold-time requirements (Figure
15). Data is shifted into the device during the rising
edge of the SCL.
Bit Read: At the end of a write operation, the master
must release the SDA bus line for the proper amount
of setup time before the next rising edge of SCL dur-
ing a bit read (Figure 15). The device shifts out each
bit of data on SDA at the falling edge of the previous
SCL pulse and the data bit is valid at the rising edge
of the current SCL pulse. Remember that the master
generates all SCL clock pulses including when it is
reading bits from the slave.
Acknowledgement (ACK and NACK): An acknowl-
edge-ment (ACK) or not acknowledge (NACK) is
always the 9th bit transmitted during a byte transfer.
The device receiving data (the master during a read
or the slave during a write operation) performs an
ACK by transmitting a zero during the 9th bit. A
device performs a NACK by transmitting a one dur-
ing the 9th bit. Timing for the ACK and NACK is
identical to all other bit writes (Figure 15). An ACK is
the acknowledgment that the device is properly
receiving data. A NACK is used to terminate a read
sequence or as an indication that the device is not
receiving data.
PON Triplexer and SFP Controller
______________________________________________________________________________________
29
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20MD18PA | CONN RCPT 18POS WALL MNT W/PINS |
| MAX7359ETG+ | IC KEY SWITCH 2WIRE 24-TQFN |
| USB-232-SS | IC USB ASYNC SRL UART 20-SSOP |
| MS27473E24F61P | CONN PLUG 61POS STRAIGHT W/PINS |
| MS27474E10F98PA | CONN RCPT 6POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1875T+ | 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1875T+T&R | 制造商:Maxim Integrated Products 功能描述:PON TRIPLEXER 38TQFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SFP CTRLR/TRIPLEXER 38-TQFN 制造商:Maxim Integrated Products 功能描述:ADC / DAC Multichannel PON Triplexer & SFP Controller |
| DS1875T+T&R | 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1875T+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer and SFP Controller |
| DS1876 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SFP Controller with Dual LDD Interface |
发布紧急采购，3分钟左右您将得到回复。