- 您现在的位置：买卖IC网 > PDF目录9755 > DS26303LN-75+ (Maxim Integrated Products)IC LIU E1/T1/J1 3.3V 144-ELQFP PDF资料下载
参数资料
| 型号： | DS26303LN-75+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 61/101页 |
| 文件大小： | 0K |
| 描述： | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 13 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 8/8 |
| 规程： | T1/E1/J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP 裸露焊盘 |
| 供应商设备封装： | 144-LQFP 裸露焊盘 |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
62 of 101
6.4.5
Bipolar Violation and Excessive Zero Detector
The DS26303 detects code violations, BPV, and excessive zero errors. The reporting of the errors is done through
the pin RNEGn/CVn.
Excessive zeros are detected if eight consecutive 0s are detected with B8ZS enabled and four consecutive 0s are
detected with HDB3 enabled. Excessive zero detection is selectable when single-rail mode and HDB3/B8ZS
encoding/decoding is selected.
The bits in the EZDE and CVDEB registers determine the combinations that are reported. Table 6-9 outlines the
functionality:
Table 6-9. BPV, Code Violation, and Excessive Zero Error Reporting
CONDITIONS
CVn PIN REPORTS
EZDE is reset, CVDEB is reset
BPV + code violation
EZDE is set, CVDEB is reset
BPV + code violation + excessive zero
EZDE is reset, CVDEB is set
BPV
EZDE is set, CVDEB is set
BPV + excessive zero
6.4.6
LIU Receiver Front-End
It is recommended that the receiver be configured as per Table 6-4 and Figure 6-4. Internal or external mode for
the receiver front end can be selected by register GC.RIMPMS. When this bit is set to external mode the user is
required to supply two 15
Ω resistors (Rt) as shown in Figure 6-4. The internal adjust resistors A75, A100, and A110
will still be set in external mode if 75
Ω, 100Ω, or 110Ω impedance is selected during template selection. However,
the internal 30
Ω resistor will be disconnected. If the user would like all the adjust resistors to be disconnected or
any internal impedance matching, then the user should set the TS.RIMPOFF bit for each LIU or the RIMPOFF pin
when in hardware mode.
6.5
Hitless-Protection Switching (HPS)
Many current redundancy protection implementations use mechanical relays to switch between primary and
backup boards. The switching time in relays is typically in the milliseconds, making T1/E1 HPS impossible. The
switching event likely causes frame-synchronization loss in any equipment downstream, affecting the quality of
service. The same is also true for tri-stating mechanisms that use software or inactive clocks for the triggering of
HPS.
The DS26303 LIU includes fast tri-statable outputs for TTIPn and TRINGn and fast turn-off impedance matching for
the RTIPn and RRINGn within less than one bit cycle. The control logic is shown in Figure 6-5. In software mode,
the user can set the RHPMC bit, which allows the OE pin to control both the transmitter outputs and the receive
impedance matching. This is a very useful function in that control can be done through a hardware pin, allowing a
quick switch to the backup system for both the receiver and the transmitter. Figure 6-6 shows a typical HPS
application in software mode where the OE pin is used for control. In hardware mode, the receiver can have
impedance matching turned off quickly by using the RIMPOFF pin, and the transmitter output can be turned off
quickly by using the OE pin.
相关PDF资料 |
PDF描述 |
|---|---|
| DS3151+ | IC LIU DS3/E3/STS-1 SGL 144CSBGA |
| VE-26X-IU-F2 | CONVERTER MOD DC/DC 5.2V 200W |
| MC100EP17DTR2G | IC RCVR/DRV ECL QUAD DFF 20TSSOP |
| DS2181AQ+T&R | IC TXRX CEPT PRIMARY RATE 44PLCC |
| MS27468T11B98PB | CONN RCPT 6POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS26303LN-75+ | 功能描述:电信线路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| DS26303LN-75+A3 | 功能描述:电信线路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| DS26303LN-75A3 | 功能描述:电信线路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| DS26303LN-XXX | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
| DS26303LN-XXX+ | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
发布紧急采购，3分钟左右您将得到回复。