- 您现在的位置：买卖IC网 > PDF目录1788 > DS2790G+T&R (Maxim Integrated Products)IC FUEL GAUGE BATT 28-TDFN PDF资料下载
参数资料
| 型号： | DS2790G+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/41页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 28-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TDFN |
| 供应商设备封装： | 28-TDFN-EP（8x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
DS2790 Programmable 1-Cell Li-Ion Fuel Gauge and Protector
Stack Memory
A 16-bit, 16-level internal stack provides storage for program return addresses and general-purpose use. The stack
is used automatically by the processor when the CALL, RET, and RETI instructions are executed and interrupts
serviced. The stack can also be used explicitly to store and retrieve data by using the PUSH, POP, and POPI
instructions.
On reset, the stack pointer, SP, initializes to the top of the stack (0Fh). The CALL, PUSH, and interrupt-vectoring
operations increment SP, then store a value at the location pointed to by SP. The RET, RETI, POP, and POPI
operations retrieve the value at “@SP” and then decrement SP.
Utility ROM
The utility ROM is a 4k word block of internal ROM memory that defaults to a starting address of 8000h. The utility
ROM consists of subroutines that can be called from application software. These include:
?
?
?
?
In-system programming (bootstrap loader) over JTAG or 2-wire interfaces
In-circuit debug routines
Internal self-test routines
callable routines for in-application EEPROM programming and SHA-1 calculations
Following any reset, execution begins in the utility ROM. The ROM software determines whether the program
execution should immediately jump to location 0000h, the start of application code, or to one of the special routines
mentioned. Routines within the utility ROM are firmware-accessible and can be called as subroutines by the
application software. More information on the utility ROM contents is contained in the MAXQ Family User's Guide:
DS2790 Supplement .
Some applications require protection against unauthorized viewing of program code memory. For these
applications, access to in-system programming, in-application programming, or in-circuit debugging functions is
prohibited until a password has been supplied. The password is defined as the 16 words of physical program
memory at addresses x0010h to x001Fh. Upon startup, code in the ROM examines the password, if a password is
defined (password is other than all zero’s or all one’s), the PWL bit remains set, which prohibits access to
commands to read memory contents over the JTAG and 2-wire interfaces.
A single Password Lock (PWL) bit is implemented in the SC register. When the PWL is set to one (power-on reset
default), the password is required to access the utility ROM, including in-circuit debug and in-system programming
routines that allow reading or writing of internal memory. When PWL is cleared to zero, these utilities are fully
accessible without password. The password is automatically set to all ones following a mass erase.
PROGRAMMING
The EEPROM memory of the microcontroller can be programmed by two different methods: in-system
programming and in-application programming. Both methods afford great flexibility in system design as well as
reduce the life-cycle cost of the embedded system. These features can be password protected to prevent
unauthorized access to code memory.
In-System Programming
An internal bootstrap loader allows the device to be programmed over the JTAG or 2-wire interfaces. As a result,
system software can be upgraded in-system, eliminating the need for a costly hardware retrofit when software
updates are required. Remote software uploads are possible that enable physically inaccessible applications to be
frequently updated. The JTAG interface hardware can be a JTAG connection to another microcontroller, or a
connection to a PC serial port using a serial to JTAG converter such as the MAXQJTAG-001, available from Maxim
Integrated Products. The 2-wire interface hardware can be an I 2 C connection to another microcontroller, or a
connection to a PC USB port using a USB to I 2 C converter such as the DS9123O, available from Dallas
Semiconductor. A commercial gang programmer can also be used for programming.
11 of 41
相关PDF资料 |
PDF描述 |
|---|---|
| DS3881E+T&R | IC CCFL CONTROL 24TSSOP |
| DS3882E+T&R | IC CCFL CNTRLR DUAL 28TSSOP |
| DS3984T+ | IC CCFL CNTRLR 4CH 32-TQFP |
| DS3988T+ | IC CCFL CNTRLR 8CH 48TQFP |
| DS3991Z+T&R/PPV | IC CTRLR CCFL PUSH-PULL 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2792G+ | 功能描述:IC PROG FUEL GAUGE W/UART 28TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| DS2792G+T&R | 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 28-TDFN |
| DS2792G+T&R | 功能描述:IC FUEL GAUGE BATT 28-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| DS28 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS280BR810ZBFT | 功能描述:Buffer, ReDriver 8 Channel 28Gbps 8-SOIC 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 类型:缓冲器，转接驱动器 应用:- 输入:CML 输出:CML 数据速率（最大值）:28Gbps 通道数:8 延迟时间:- 信号调节:- 电容 - 输入:- 电压 - 电源:2.5V 电流 - 电源:- 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。