- 您现在的位置：买卖IC网 > PDF目录1788 > DS2790G+T&R (Maxim Integrated Products)IC FUEL GAUGE BATT 28-TDFN PDF资料下载
参数资料
| 型号： | DS2790G+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 36/41页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 28-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TDFN |
| 供应商设备封装： | 28-TDFN-EP（8x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页
DS2790 Programmable 1-Cell Li-Ion Fuel Gauge and Protector
CC = ( Overvoltage ) and ( Undervoltage ) and ( Overcurrent , Charge Direction) and ( Charge Overtemperature
if enabled) and ( Charge Undertemperature if enabled) and (CE = 1) and SLEEP
Protection Register
The Protection Register allows system software to determine if a protection fault condition has occurred and what
triggered the protection fault. When a protection fault occurs, its corresponding protection flag is set. The flag will
remain set until system software clears the bit after the fault is no longer present. System software can also disable
charging or discharging by clearing the charge enable or discharge enable bits, or system software can completely
disable the ADC and/or the protection FETs using the PMM bits. There is no way for system software to override a
fault condition and enable the FETs.
Figure 19. Protection Register Format (PROT)
FIELD
COCF
DOCF
SCF
OVF
UVF
Reserved
CC
DC
Reserved
BIT
15
14
13
12
11
10
9
8
7:4
FORMAT
R/W
R/W
R/W
R/W
R/W
Read Only
Read Only
Read Only
Read Only
DEFINITION
Charge Overcurrent Flag. Set to 1 by an COC fault condition.
Can only be reset by system software after fault is corrected.
Discharge Overcurrent Flag. Set to 1 by a DOC fault condition.
Can only be reset by system software after fault is corrected.
Short Circuit Flag. Set to 1 by a SC fault condition. Can only be
reset by system software after fault is corrected.
Overvoltage Flag. Set to 1 by an OV fault condition. Can only be
reset by system software after fault is corrected.
Undervoltage Flag. Set to 1 by a UV fault condition. Can only be
reset by system software after fault is corrected.
Undefined
CC Pin Mirror. This bit mirrors the state of the CC pin.
DC Pin Mirror. This bit mirrors the state of the DC pin.
Undefined
Charge Enable.
CE
3
R/W
0 = Charge FET is disabled.
1 = Charge FET is enabled unless disabled by fault.
Writing this bit to 1 will not override a fault condition.
Discharge Enable.
DE
2
R/W
0 = Discharge FET is disabled.
1 = Discharge FET is enabled unless disabled by fault.
Writing this bit to 1 will not override a fault condition.
Protection and Measurement Modes.
0 0 = ADC disabled, CC and DC low.
PMM
1:0
R/W
0 1 = ADC enabled, CC and DC low.
1 0 = ADC enabled, CC and DC low.
1 1 = ADC enabled, CC and DC high.
Adjusting Protection Thresholds
The protection thresholds are set in two locations. The Charge Overcurrent threshold, Discharge Overcurrent
threshold, Short-Circuit Current threshold, and Short-Circuit Delay thresholds are set in the ADC Configuration
Register location 600Ah. Values for Overvoltage, Undervoltage, and all temperature thresholds are stored in the
password protected memory. See the Password Protected User Trim section.
High Side N-Channel Protection FETs
The DS2790 controls charging and discharging through external high-side N-FETs controlled through the CC and
DC pins. An internal charge pump generates the voltage needed to drive the external FETs. An external capacitor
connected between the CP and VSS pins stores the charge needed for the DS2790 to maintain the CC and DC
outputs. To disable discharging, the DS2790 internally connects DC to V SS . To disable charging, the DS2790
internally connects CC to V DD . To enable charging or discharging, the DS2790 drives the appropriate FET gate to
36 of 41
相关PDF资料 |
PDF描述 |
|---|---|
| DS3881E+T&R | IC CCFL CONTROL 24TSSOP |
| DS3882E+T&R | IC CCFL CNTRLR DUAL 28TSSOP |
| DS3984T+ | IC CCFL CNTRLR 4CH 32-TQFP |
| DS3988T+ | IC CCFL CNTRLR 8CH 48TQFP |
| DS3991Z+T&R/PPV | IC CTRLR CCFL PUSH-PULL 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2792G+ | 功能描述:IC PROG FUEL GAUGE W/UART 28TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| DS2792G+T&R | 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 28-TDFN |
| DS2792G+T&R | 功能描述:IC FUEL GAUGE BATT 28-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| DS28 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS280BR810ZBFT | 功能描述:Buffer, ReDriver 8 Channel 28Gbps 8-SOIC 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 类型:缓冲器，转接驱动器 应用:- 输入:CML 输出:CML 数据速率（最大值）:28Gbps 通道数:8 延迟时间:- 信号调节:- 电容 - 输入:- 电压 - 电源:2.5V 电流 - 电源:- 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。