- 您现在的位置：买卖IC网 > PDF目录97869 > DS3112 (DALLAS SEMICONDUCTOR) DATACOM, FRAMER, PBGA256 PDF资料下载
参数资料
| 型号： | DS3112 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PBGA256 |
| 封装： | 27 X 27 MM, PLASTIC, BGA-256 |
| 文件页数： | 126/134页 |
| 文件大小： | 900K |
| 代理商： | DS3112 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页当前第126页第127页第128页第129页第130页第131页第132页第133页第134页
DS3112
91 of 134
Transmit Operation
On reset, the transmit HDLC controller will flush the transmit FIFO and transmit an abort followed by
either 7Eh or FFh (depends on the setting of the TFS control bit) continuously. The transmit HDLC then
waits until there are at least two bytes in the transmit FIFO before beginning to send the packet. The
transmit HDLC will automatically add an opening flag of 7Eh to the beginning of the packet and zero
stuff the outgoing datastream. When the transmit HDLC controller detects that the TMEND bit in the
transmit FIFO is set, it will automatically calculate and add in the 16-bit CRC checksum followed by a
closing flag of 7Eh. If the FIFO is empty, then it will begin sending either 7Eh or FFh continuously. If
there is some more data in the FIFO, then the transmit HDLC will automatically add in the opening flag
and begin sending the next packet. Between consecutive packets, there are always at least two flags of
7Eh. If the transmit FIFO ever empties when a packet is being sent (i.e. before the TMEND bit is set),
then the transmit HDLC controller will send an abort of seven ones in a row (FEh) followed by a
continuous transmission of either 7Eh (flags) or FFh (idle) and the Transmit FIFO Underrun (TUDR)
status bit will be set. When the FIFO underruns, the transmit HDLC controller should be reset by the
Host.
The transmit HDLC has been designed to minimize it’s real time Host support requirements. The
transmit FIFO is 256 bytes which is deep enough to store the three T3 packets (Path ID, Idle Signal ID,
and Test Signal ID) that need to be sent once a second. Hence in T3 applications, the Host only needs to
access the transmit HDLC once a second to load up the three messages. Once the Host has loaded an
outgoing packet, it can monitor the Transmit Packet End (TEND) status bit to know when the packet has
finished being transmitted.
Also the Host can be notified when the FIFO has emptied below a
programmable level called the low water mark. The Host must never overfill the FIFO. To keep this
from occurring, the Host can obtain the real time depth of the transmit FIFO via the Transmit FIFO Level
bits in the HDLC Status Register (HSR).
9.2 HDLC CONTROL AND FIFO REGISTER DESCRIPTION
Register Name:
HCR
Register Description:
HDLC Control Register
Register Address:
80h
Bit #
7
654
321
0
Name
n/a
RHR
THR
TFS
n/a
TCRCI
TZSD
TCRCD
Default
-
000
-
0
Bit #
15
14
13
12
11
10
9
8
Name
RHWMS2 RHWMS1
RHWMS0
TLWMS2
TLWMS1
TLWMS0 RID
TID
Default
0
Note: Bits that are underlined are read only; all other bits are read-write.
Bit 0 / Transmit CRC Defeat (TCRCD). When this bit is set low, the HDLC will automatically
calculate and append the 16 bit CRC to the outgoing HDLC message. When this bit is set high, the
device will not append the CRC to the outgoing message.
0 = enable CRC generation (normal operation)
1 = disable CRC generation
相关PDF资料 |
PDF描述 |
|---|---|
| DS3131 | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| DS3134 | DATACOM, FRAMER, PBGA256 |
| DS3150QN | DATACOM, PCM TRANSCEIVER, PQCC28 |
| DS3150Q | DATACOM, PCM TRANSCEIVER, PQCC28 |
| DS3150TN | DATACOM, PCM TRANSCEIVER, PDIP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3112+ | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112+W | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112D1 | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112D1+ | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112DK | 功能描述:网络开发工具 DS3112 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。