参数资料
| 型号： | DS33R11DK |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/44页 |
| 文件大小： | 0K |
| 描述： | KIT DESIGN FOR DS33R11 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 设计资源： | DS33R11DK Gerber Files |
| 标准包装： | 1 |
| 主要目的： | 接口，以太网 |
| 已用 IC / 零件： | DS33R11 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
DS33R11DK/DS33ZH11DK
BASIC OPERATION
Powering Up the Design Kit
?
?
Connect PCB 3.3V and GND banana plugs to power supply. A 2A supply is recommended. At steady-state, the
system should draw approximately 700mA.
General
?
?
Upon power-up, the DS33R11 Queue overflow LED (DS02 red) will not be lit; also, the INT LED (DS01 red) will
not be lit. PHY LINK LED (DS07 green) should be lit if the Ethernet is connected. Transceiver RLOS LED
(DS05 red) will be lit.
DS33ZH11 does not have Queue overflow or INT pins. DS21348 and DS3150 RLOS LEDs (DS15 and DS13
red) will be lit.
Following are several basic system initializations.
Basic DS33R11 Initialization
This section covers two basic methods for configuring the DS33R11.
1. Device-Driver Based Configuration. If the pins J09.4+J09.6 are jumpered, the device driver autoconfigures
the DS33R11 upon power-up. This enables traffic to pass from the Ethernet port to the serial port. Consult
the device driver documentation for further details.
2. Register-Based Configuration. Launch ChipView.exe and select Register View. When prompted for a
definition file, pick the file named DS33Z11.def . Three definition files will load: DS33Z11 control, DS33Z11
port, and DS2155 transceiver. Go to the File menu and select File → Memory Config File → Load .MFG file.
When prompted, select the file named
basic_config.mfg . Following this, load the file
e1_gapclk_crc4_hdb3_nocas.ini using the menu selection File → Initalization Config File → Load .INI file.
Additional Configuration for DS33R11
?
?
?
Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment. This should
cause the link LED to turn on.
Place a loopback connector at the T1E1 network side; RLOS LED DS05 should go out.
At this point any packets sent to the DS33R11 are echoed back. Incoming packets (i.e., ping) should cause the
RX LED to blink, after which the TX LED should also blink.
10 of 44
相关PDF资料 |
PDF描述 |
|---|---|
| DS33Z41DK | KIT DESIGN FOR DS33Z41 |
| DS9097E# | COM PORT ADAPTER |
| DS9097U-E25# | ADAPTER COM PORT RS232 DB-25 |
| DS9490R# | IC BRIDGE USB TO 1-WIRE RJ11 |
| DST1E1DK | KIT DESIGN SCT T1/E1 DS21X5Y |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS33R41 | 功能描述:网络控制器与处理器 IC Inv-Mult Enet Mapper w/Quad T1/E1/J1 Trx RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33R41+ | 功能描述:网络控制器与处理器 IC Inv-Mult Enet Mapper w/Quad T1/E1/J1 Trx RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33W11+ | 功能描述:网络控制器与处理器 IC Ethernet Over PDH Mapping Devices RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33W11DK+ | 功能描述:以太网开发工具 1/1 E-Net - PDH Design Kit RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| DS33W41+ | 功能描述:网络控制器与处理器 IC Ethernet Over PDH Mapping Devices RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。