参数资料
| 型号： | DS33R11DK |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/44页 |
| 文件大小： | 0K |
| 描述： | KIT DESIGN FOR DS33R11 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 设计资源： | DS33R11DK Gerber Files |
| 标准包装： | 1 |
| 主要目的： | 接口，以太网 |
| 已用 IC / 零件： | DS33R11 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
DS33R11DK/DS33ZH11DK
Basic DS33ZH11 Initialization
This section covers the EEPROM methods for configuring the DS33ZH11.
1) If the HWMODE jumper is installed, the DS33ZH11 will retrieve configuration settings from the on-board
EEPROM during power-up.
2) Select which serial device to use: either the DS3150 T3E3 LIU or the DS21348 T1E1 LIU can be selected. In
making this selection the backplane jumpers JP05–JP08 must be installed to select between the two serial
devices. Connecting pins 2+3 of each jumper selects the DS3150, connecting pins 1+2 of each jumper selects
the DS21348.
Additional Configuration for DS33ZH11
?
?
?
Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment. This should
cause the link LED to turn on.
Place a loopback connector at the network side; the RLOS LED should go out. The RLOS LED is DS15 for
T1E1 and DS13 for T3E3.
At this point any packets sent to the DS33ZH11 are echoed back. Incoming packets (i.e., ping) should cause
the RX LED to blink, after which the TX LED should also blink.
Monitor and Capture Ethernet Traffic
?
?
?
?
Although ping is mentioned, it is not recommended. The ping command goes through the computer’s TCPIP
stack, and sometimes is not sent out the PC’s network connector (i.e., if the PC’s ARP cache is out of date).
Additionally, ping requires two PCs, as a PC with only one adapter cannot ping itself (a local ping gets sent to a
local host instead of out the connector). However, note that ping is still a valuable test once the prototyping
stage is complete.
Generation and capture of arbitrary (raw) packets can be accomplished using CommView. A time-limited demo
is available at the website www.tamos.com/products/commview .
Ethereal is an excellent (and free) packet capture utility. Download at www.ethereal.com .
Adding additional Ethernet ports to a PC is rather simple when a USB-to-Ethernet adapter is used. This allows
for end-to-end testing using a single PC. When using two adapters, the PC has a different IP address for each
adapter. Test equipment allows selection of either adapter. Operating system-based network traffic is sent out
the default adapter. Typically, this is the adapter that has recently had connection to a live network.
11 of 44
相关PDF资料 |
PDF描述 |
|---|---|
| DS33Z41DK | KIT DESIGN FOR DS33Z41 |
| DS9097E# | COM PORT ADAPTER |
| DS9097U-E25# | ADAPTER COM PORT RS232 DB-25 |
| DS9490R# | IC BRIDGE USB TO 1-WIRE RJ11 |
| DST1E1DK | KIT DESIGN SCT T1/E1 DS21X5Y |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS33R41 | 功能描述:网络控制器与处理器 IC Inv-Mult Enet Mapper w/Quad T1/E1/J1 Trx RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33R41+ | 功能描述:网络控制器与处理器 IC Inv-Mult Enet Mapper w/Quad T1/E1/J1 Trx RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33W11+ | 功能描述:网络控制器与处理器 IC Ethernet Over PDH Mapping Devices RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33W11DK+ | 功能描述:以太网开发工具 1/1 E-Net - PDH Design Kit RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| DS33W41+ | 功能描述:网络控制器与处理器 IC Ethernet Over PDH Mapping Devices RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。