- 您现在的位置：买卖IC网 > PDF目录299028 > EMC2103-1-KP-TR (STANDARD MICROSYSTEMS CORP) PDF资料下载
参数资料
| 型号： | EMC2103-1-KP-TR |
| 厂商： | STANDARD MICROSYSTEMS CORP |
| 元件分类： | 模拟信号调理 |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC12 |
| 封装： | 4 X 4 MM, ROHS COMPLIANT, QFN-12 |
| 文件页数： | 14/89页 |
| 文件大小： | 1243K |
| 代理商： | EMC2103-1-KP-TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
SMSC EMC2103
21
Revision 0.90 (08-19-08)
DATASHEET
The EMC2103 will respond to the ARA in the following way if the ALERT pin is asserted.
1. Send Slave Address and verify that full slave address was sent (i.e. the SMBus communication
from the device was not prematurely stopped due to a bus contention event).
2. Set the MASK bit to clear the ALERT pin.
4.7
SMBus Address
The EMC2103 SMBus Address is fixed at 0101_110xb.
Other addresses are available. Contact SMSC for details.
Attempting to communicate with the EMC2103 SMBus interface with an invalid slave address or invalid
protocol will result in no response from the device and will not affect its register contents.
4.8
SMBus Time-out
The EMC2103 includes an SMBus time-out feature. Following a 30ms period of inactivity on the
SMBus, the device will time-out and reset the SMBus interface.
4.9
Programming from EEPROM
Programming from EEPROM is only available for EMC2103-4 device. When enabled via the
SHDN_SEL pin (see Section 5.1.1), the EMC2103 will attempt to program itself from an EEPROM.
During this time, the EMC2103 acts as a simple SMBus Master to read data from a connected
EEPROM using the following procedure.
1. After power-up the EMC2103 waits for 10ms with the SMDATA and SMCLK pins tri-stated.
2. Once the wait period has elapsed, the EMC2103 sends a START signal followed by the 7 bit client
address 1010_000b followed by a ‘0’ and waits for an ACK signal from the EEPROM.
3. When the EEPROM sends the ACK signal, the EMC2103 will send a second start signal and
continue sending the Block Read Command (see Table 4.7) to the same slave address. It reads
256 data bytes from the EEPROM sending an ACK between each data byte. When 256 data bytes
have been received, it sends a NACK signal followed by a STOP bit.
4. Resets the device as an SMBus Client with slave address 0101_110xb.
If the EMC2103 does not receive an acknowledge bit from the EEPROM then the following will occur:
1. The ALERT pin will be asserted and will remain asserted until a Host device initiates
communication with the EMC2103 and reads the Status Register. The ALERT pin will be de-
asserted after a single Status Register read.
2. The EMC2103 will reset its SMBus protocol as a slave interface and start operating from the default
conditions with slave address 0101_110xb.
Table 4.7 Block Read Byte Protocol
START
SLAVE
ADDRESS
WR
ACK
Register
Address
ACK
START
SLAVE
ADDRESS
RD
ACK
Register
Data (00h)
. . .
0 -> 1
1010_000
0
00h
0
0 -> 1
1010_000
1
0
XXh
. . .
ACK
Register
Data (01h)
ACK
Register
Data (02h)
ACK
Register
Data (02h)
. . .
ACK
Register
Data (FFh)
NACK
STOP
0
XXh
0
XXh
0
XXh
. . .
0
XXh
1
1 -> 0
相关PDF资料 |
PDF描述 |
|---|---|
| EMC2103-2-AP-TR | |
| EMCL12C2J-35.000MTR | CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT |
| EMCL12C2J-40.000M | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
| EMCL12D2H-30.000MTR | CRYSTAL OSCILLATOR, CLOCK, 30 MHz, LVPECL OUTPUT |
| EMCL12D2H-40.000MTR | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EMC2103-2 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
| EMC2103-2-AP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-2-AP-TR | 功能描述:板上安装温度传感器 Closed Loop RPM RPM Fan Ctrl 3Remote RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| EMC2103-3-KP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-4 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
发布紧急采购，3分钟左右您将得到回复。