参数资料
型号: EMC2103-1-KP-TR
厂商: STANDARD MICROSYSTEMS CORP
元件分类: 模拟信号调理
中文描述: SPECIALTY ANALOG CIRCUIT, QCC12
封装: 4 X 4 MM, ROHS COMPLIANT, QFN-12
文件页数: 48/89页
文件大小: 1243K
代理商: EMC2103-1-KP-TR
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
Revision 0.90 (08-19-08)
52
SMSC EMC2103
DATASHEET
6.11
Configuration 2 Register
The Configuration 2 Register controls conversion rate of the temperature monitoring as well as the
fault queue.
Bit 6 - DIS_DYN - Disables the Dynamic Averaging Feature.
‘0’ (default) - The Dynamic Averaging function is enabled. The conversion time for all temperature
channels is scaled based on the chosen conversion rate to maximize accuracy and immunity to
random temperature measurement variation.
‘1’ - The Dynamic Averaging function is disabled. The conversion time for all temperature channels
is fixed regardless of the chosen conversion rate.
Bit 5 - DIS_TO - Disables the SMBus time out function.
‘0’ (default) - The SMBus time out function is enabled.
‘1’ - The SMBus time out function is disabled allowing the device to be fully I2C compliant.
Bit 4 - DIS_AVG - Disables digital averaging of the External Diode channels.
‘0’ (default) - The External Diode channels have digital averaging enabled. The temperature data
is the average of the previous four measurements.
‘1’ - The External Diode channels have digital averaging disabled. The temperature data is the last
measured data.
Bits 3-2 - QUEUE[1:0] - Determines the number of consecutive out of limit conditions that are
necessary to trigger an interrupt. Each measurement channel has a separate fault queue associated
with the high limit, low limit, and diode fault condition.
APPLICATION NOTE: If the fault queue for any channel is currently active (i.e. an out of limit condition has been
detected and caused the fault queue to increment) then changing the settings will not take
effect until the fault queue is zeroed. This occurs by the ALERT pin asserting or the out of
limit condition being removed.
Bit 1 - 0 - CONV[1:0] - determines the conversion rate of the temperature monitoring. This conversion
rate does not affect the fan driver. The supply current from VDD_3V is nominally dependent upon the
conversion rate and the average current will increase as the conversion rate increases.
Table 6.16 Configuration 2 Register
ADDR
R/W
REGISTER
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
21h
R/W
Config 2
-
DIS_D
YN
DIS_
TO
DIS_
AVG
QUEUE[1:0]
CONV[1:0]
0Eh
Table 6.17 Fault Queue
QUEUE[1:0]
NUMBER OF CONSECUTIVE OUT OF LIMIT CONDITIONS
10
0
1 (disabled)
01
2
10
3
1
4 (default)
相关PDF资料
PDF描述
EMC2103-2-AP-TR
EMCL12C2J-35.000MTR CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT
EMCL12C2J-40.000M CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT
EMCL12D2H-30.000MTR CRYSTAL OSCILLATOR, CLOCK, 30 MHz, LVPECL OUTPUT
EMCL12D2H-40.000MTR CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT
相关代理商/技术参数
参数描述
EMC2103-2 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide
EMC2103-2-AP 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown
EMC2103-2-AP-TR 功能描述:板上安装温度传感器 Closed Loop RPM RPM Fan Ctrl 3Remote RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
EMC2103-3-KP 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown
EMC2103-4 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide