- 您现在的位置：买卖IC网 > PDF目录299028 > EMC2103-1-KP-TR (STANDARD MICROSYSTEMS CORP) PDF资料下载
参数资料
| 型号： | EMC2103-1-KP-TR |
| 厂商： | STANDARD MICROSYSTEMS CORP |
| 元件分类： | 模拟信号调理 |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC12 |
| 封装： | 4 X 4 MM, ROHS COMPLIANT, QFN-12 |
| 文件页数： | 27/89页 |
| 文件大小： | 1243K |
| 代理商： | EMC2103-1-KP-TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
SMSC EMC2103
33
Revision 0.90 (08-19-08)
DATASHEET
5.7
Spin Up Routine
The EMC2103 also contains programmable circuitry to control the spin up behavior of the fan driver
to ensure proper fan operation. The Spin Up Routine is initiated under the following conditions when
the Tach Period Measurement method of tach measurement is used. This applies to either the RPM
based Fan Speed Control Algorithm mode or the Direct Setting mode (with or without the Look Up
Table).
1. The TACH Target Register value changes from a value of FFh to a value that is less than the Valid
TACH Count.
2. The RPM based Fan Speed Control Algorithm’s measured TACH Reading Register value is greater
than the Valid TACH Count setting.
When the Spin Up Routine is operating, the fan driver is set to full scale (optional) for one quarter of
the total user defined spin up time. For the remaining spin up time, the fan driver output is set a a user
defined level (30% through 65% drive).
After the Spin Up Routine has finished, the EMC2103 measures the TACH signal. If the measured
TACH Reading Register value is higher than the Valid TACH Count Register setting, the FAN_SPIN
status bit is set and the Spin Up Routine will automatically attempt to restart the fan.
Figure 5.5 shows an example of the Spin Up Routine in response to a programmed fan speed change
based on the first condition above.
Figure 5.5 Spin Up Routine
100%
(optional)
30% through 65%
Algorithm controlled drive
Fan Step
Spin Up Time
of Spin Up Time
Update Time
Target Count
Changed
Target Count
Reached
New Target Count
Prev Target
Count = FFh
Check TACH
相关PDF资料 |
PDF描述 |
|---|---|
| EMC2103-2-AP-TR | |
| EMCL12C2J-35.000MTR | CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT |
| EMCL12C2J-40.000M | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
| EMCL12D2H-30.000MTR | CRYSTAL OSCILLATOR, CLOCK, 30 MHz, LVPECL OUTPUT |
| EMCL12D2H-40.000MTR | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EMC2103-2 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
| EMC2103-2-AP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-2-AP-TR | 功能描述:板上安装温度传感器 Closed Loop RPM RPM Fan Ctrl 3Remote RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| EMC2103-3-KP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-4 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
发布紧急采购，3分钟左右您将得到回复。