- 您现在的位置：买卖IC网 > PDF目录299028 > EMC2103-1-KP-TR (STANDARD MICROSYSTEMS CORP) PDF资料下载
参数资料
| 型号： | EMC2103-1-KP-TR |
| 厂商： | STANDARD MICROSYSTEMS CORP |
| 元件分类： | 模拟信号调理 |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC12 |
| 封装： | 4 X 4 MM, ROHS COMPLIANT, QFN-12 |
| 文件页数： | 62/89页 |
| 文件大小： | 1243K |
| 代理商： | EMC2103-1-KP-TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页当前第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
SMSC EMC2103
65
Revision 0.90 (08-19-08)
DATASHEET
If a TACH Target setting is set above the Valid TACH Count setting, then that setting will be ignored
and the algorithm will use the current fan drive setting.
The Valid TACH Count Register is software locked.
6.29
Fan Drive Fail Band Registers
The Fan Drive Fail Band Registers store the number of tach counts used by the Fan Drive Fail
detection circuitry. This circuitry is activated when the fan drive setting high byte is at FFh. When it is
enabled, the actual measured fan speed is compared against the target fan speed.
This circuitry is used to indicate that the target fan speed at full drive is higher than the fan is actually
capable of reaching. If the measured fan speed does not exceed the target fan speed minus the Fan
Drive Fail Band Register settings for a period of time longer than set by the DRIVE_FAIL_CNTx[1:0]
bits then the DRIVE_FAIL status bit will be set and an interrupt generated.
6.30
TACH Target Register
The TACH Target Register holds the target tachometer value that is maintained by the RPM based
Fan Speed Control Algorithm.
The value in the TACH Target Register will always reflect the current TACH Target value. If the Look
Up Table is active and configured to operate in RPM Mode, then this register will be read only. Writing
to this register will have no affect and the data will not be stored.
If the algorithm is enabled then setting the TACH Target Register to FFh will disable the fan driver (set
the PWM duty cycle to 0%). Setting the TACH Target to any other value (from a setting of FFh) will
cause the algorithm to invoke the Spin Up Routine after which it will function normally.
Table 6.46 Fan Drive Fail Band Registers
ADDR
R/W
REGISTER
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
4Ah
R/W
Fan Drive
Fail Band
Low Byte
16
8
4
2
1
-
00h
4Bh
R/W
Fan Drive
Fail Band
High Byte
4096
2048
1024
512
256
128
64
32
00h
Table 6.47 TACH Target Register
ADDR
R/W
REGISTER
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
4Ch
R/W
Fan TACH
Target Low
Byte
16
84
21
-
F8h
4Dh
R/W
TACH Target
4096
2048
1024
512
256
128
64
32
FFh
相关PDF资料 |
PDF描述 |
|---|---|
| EMC2103-2-AP-TR | |
| EMCL12C2J-35.000MTR | CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT |
| EMCL12C2J-40.000M | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
| EMCL12D2H-30.000MTR | CRYSTAL OSCILLATOR, CLOCK, 30 MHz, LVPECL OUTPUT |
| EMCL12D2H-40.000MTR | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EMC2103-2 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
| EMC2103-2-AP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-2-AP-TR | 功能描述:板上安装温度传感器 Closed Loop RPM RPM Fan Ctrl 3Remote RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| EMC2103-3-KP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-4 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
发布紧急采购，3分钟左右您将得到回复。