- 您现在的位置：买卖IC网 > PDF目录299028 > EMC2103-1-KP-TR (STANDARD MICROSYSTEMS CORP) PDF资料下载
参数资料
| 型号： | EMC2103-1-KP-TR |
| 厂商： | STANDARD MICROSYSTEMS CORP |
| 元件分类： | 模拟信号调理 |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC12 |
| 封装： | 4 X 4 MM, ROHS COMPLIANT, QFN-12 |
| 文件页数： | 22/89页 |
| 文件大小： | 1243K |
| 代理商： | EMC2103-1-KP-TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
SMSC EMC2103
29
Revision 0.90 (08-19-08)
DATASHEET
5.4.1
Programming the Look Up Table
When the Look Up Table is used, it must be loaded and configured correctly based on the system
requirements. The following steps outline the procedure.
1. Determine whether the Look Up Table will drive a PWM duty cycle or a tachometer target value
and set the RPM / PWM bit in the Fan LUT Configuration Register (see Section 6.32).
2. Determine which measurement channels (up to four) are to be used with the Look Up Table and
set the TEMP3_CFG and TEMP4_CFG bits accordingly in the Fan LUT Configuration Register.
3. For each step to be used in the LUT, set the Fan Setting (either PWM or TACH Target as set by
the RPM / PWM bit). If a setting is not used, then set it to FFh (if a PWM) or 00h (if a TACH Target).
Load the lowest settings first in ascending order (i.e. Fan Setting 1 is the lowest setting greater
than “off”. Fan Setting 2 is the next highest setting, etc.). See Section 6.33.
4. For each step to be used in the LUT, set each of the measurement channel thresholds. These
values must be set in the same data format that the data is presented. If DTS is to be used, then
the format should be in temperature with a maximum threshold of 100°C (64h). If a measurement
channel is not used, then set the threshold at FFh.
5. Update the threshold hysteresis to be smaller than the smallest table step.
6. Configure the RPM based Fan Speed Control Algorithm if it is to be used. See Section 5.5.1 for
more details.
Figure 5.3 Fan Control Look-Up Table Example
Time
Fan
Setting
Temp
S2
S3
S4
T4
T5
T6
Averaged
Temperature
T4 - Hyst
T5 - Hyst
T6 - Hyst
S1
T3
T3 - Hyst
T2
T2 - Hyst
S6
T1
S5
Measurement taken
Fan
Setting
相关PDF资料 |
PDF描述 |
|---|---|
| EMC2103-2-AP-TR | |
| EMCL12C2J-35.000MTR | CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT |
| EMCL12C2J-40.000M | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
| EMCL12D2H-30.000MTR | CRYSTAL OSCILLATOR, CLOCK, 30 MHz, LVPECL OUTPUT |
| EMCL12D2H-40.000MTR | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EMC2103-2 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
| EMC2103-2-AP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-2-AP-TR | 功能描述:板上安装温度传感器 Closed Loop RPM RPM Fan Ctrl 3Remote RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| EMC2103-3-KP | 制造商:SMSC 制造商全称:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown |
| EMC2103-4 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Analog and Interface Product Selector Guide |
发布紧急采购，3分钟左右您将得到回复。