- 您现在的位置：买卖IC网 > PDF目录67504 > FM4005-G SPECIALTY CONSUMER CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | FM4005-G |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| 封装： | GREEN, MS-012AB, SOIC-14 |
| 文件页数： | 19/23页 |
| 文件大小： | 244K |
| 代理商： | FM4005-G |
N
O
T R
EC
O
M
EN
D
ED
FO
R
N
EW
D
ES
IG
N
S
Al
te
rn
at
iv
es
: F
M
31
27
2
(5
V)
or
FM
31
L2
72
(3
V)
FM4005
Rev. 2.4
Jan. 2010
Page 5 of 23
Manual Reset
The /RST pin is bi-directional and allows the
FM4005 to filter and de-bounce a manual reset
switch. The /RST input detects an external low
condition and responds by driving the /RST signal
low for 100 ms. Note that an internal weak pull-up on
/RST eliminates the need for additional external
components.
Figure 4. Manual Reset
Reset Flags
In case of a reset condition, a flag will be set to
indicate the source of the reset. A low VDD reset or
manual reset is indicated by the POR flag, register
09h bit 6. A watchdog reset is indicated by the WTR
flag, register 09h bit 7. Note that the bits are
internally set in response to reset sources, but they
must be cleared by the user. When the register is
read, it is possible that both flags are set if both have
occurred since the user last cleared them.
Early Power Fail Comparator
An early power fail warning can be provided to the
processor well before VDD drops out of spec. The
comparator is used to create a power fail interrupt
(NMI). This can be accomplished by connecting the
PFI pin to the unregulated power supply via a resistor
divider. An application circuit is shown below. The
voltage on the PFI input pin is compared to an
onboard 1.2V reference. When the PFI input voltage
drops below this threshold, the comparator will drive
the CAL/PFO pin to a low state. The comparator has
350 mV (max) of hysteresis to reduce noise
sensitivity, only for a rising PFI signal. For a falling
PFI edge, there is no hysteresis.
Figure 5. Comparator as a Power-fail Warning
The comparator is a general purpose device and its
application is not limited to the NMI function.
The comparator is not integrated into the special
function registers except as it shares its output pin
with the CAL output. When the RTC calibration
mode is invoked by setting the CAL bit (register 00h,
bit 2), the CAL/PFO output pin will be driven with a
512 Hz square wave and the comparator will be
ignored. Since most users only invoke the calibration
mode during production, this should have no impact
on system operations using the comparator.
Note: The maximum voltage on the comparator input PFI
is limited to 3.75V under normal operating conditions.
Event Counter
The FM4005 offers the user two battery-backed event
counters. The input pins CNT1 and CNT2 are
programmable edge detectors. Each controls a 16-bit
counter. When an edge occurs, the counters will
increment their respective registers. Counter 1 is
located in registers 0Dh and 0Eh. Counter 2 is
located in registers 0Fh and 10h. These register
values can be read anytime VDD is above VTP, and
they will be incremented as long as a valid VBAK
power source is provided. To read, set the RC bit
register 0Ch bit 3 to 1. This takes a snapshot of all
four counter bytes allowing a stable value even if a
count occurs during the read. The registers can be
written by software allowing the counters to be
cleared or initialized by the system. Counts are
blocked during a write operation. The two counters
can be cascaded to create a single 32-bit counter by
setting the CC control bit (register 0Ch). When
cascaded, the CNT1 input will cause the counter to
increment. CNT2 is not used in this mode.
The control bits for event counting are located in
register 0Ch. Counter 1 Polarity is bit C1P, bit 0;
FM4005
RST
MCU
Switch
Behavior
RST
FM4005
drives
100 ms
Reset
Switch
+
-
1.2V ref
Regulator
VDD
FM4005
To MCU
NMI input
CAL/PFO
相关PDF资料 |
PDF描述 |
|---|---|
| FME270-461/ES | 1 FUNCTIONS, 400 V, 1.5 A, DATA LINE FILTER |
| FME270-461V/ES | 1 FUNCTIONS, 400 V, 1.5 A, DATA LINE FILTER |
| FME270-461W/ES | 1 FUNCTIONS, 400 V, 1.5 A, DATA LINE FILTER |
| FME270-461Y/ES | 1 FUNCTIONS, 400 V, 1.5 A, DATA LINE FILTER |
| FME270-461Z/ES | 1 FUNCTIONS, 400 V, 1.5 A, DATA LINE FILTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FM4005-GTR | 功能描述:F-RAM RTC RTC Alarm Pwr Mon WDT Bat Sw RoHS:否 存储容量:512 Kbit 组织:64 K x 8 接口:SPI 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube 制造商:Cypress Semiconductor |
| FM4005-L | 制造商:FORMOSA 制造商全称:Formosa MS 功能描述:Chip Silicon Rectifier - Glass passivated type |
| FM4005M | 制造商:WEITRON 制造商全称:Weitron Technology 功能描述:Surface Mount Standard Recovery Glass Passivated Rectifiers |
| FM4005-M | 制造商:FORMOSA 制造商全称:Formosa MS 功能描述:Glass passivated type |
| FM4005MH | 制造商:WEITRON 制造商全称:Weitron Technology 功能描述:Surface Mount Standard Recovery Glass Passivated Rectifiers |
发布紧急采购，3分钟左右您将得到回复。