参数资料
| 型号： | FS6377-01IG-XTP |
| 厂商： | ON Semiconductor |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GEN PLL PROG 16SOIC |
| 标准包装： | 3,000 |
| 类型： | PLL 时钟发生器 |
| PLL： | 是 |
| 输入： | 晶体 |
| 输出： | CMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:4 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 230MHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
FS6377
3.2 Post Divider Muxes
As shown in Figure 2, an input mux in front of each post divider stage can select from any one of the PLL frequencies or the reference
frequency. The frequency selection is done via the I
2C-bus.
The input frequency on two of the four muxes (mux C and D in Figure 2) can be changed without reprogramming by a logic-level input
on the SEL_CD pin.
3.3 Post Dividers
The post divider performs several useful functions. First, it allows the VCO to be operated in a narrower range of speeds compared to
the variety of output clock speeds that the device is required to generate. Second, it changes the basic PLL equation to
where NF, NR and NP are the feedback, reference and post divider moduli respectively, and fCLK and fREF are the output and reference
oscillator frequencies. The extra integer in the denominator permits more flexibility in the programming of the loop for many applications
where frequencies must be achieved exactly.
The modulus on two of the four post dividers muxes (post dividers C and D in Figure 2) can be altered without reprogramming by a
logic level on the SEL_CD pin.
4.0 Device Operation
The FS6377 powers up with all internal registers cleared to zero, delivering the crystal frequency to all outputs. For operation to occur,
the registers must be loaded in a most significant-bit (MSB) to least-significant-bit (LSB) order. The register mapping of the FS6377 is
shown in Table 3, and I
2C-bus programming information is detailed in Section 5.0.
Control of the reference, feedback and post dividers is detailed in Table 5. Selection of these dividers directly controls how fast the VCO
will run. The maximum VCO speed is noted in
Table 13.
4.1 SEL_CD Input
The SEL_CD pin provides a way to alter the operation of PLL C, muxes C and D and post dividers C and D without having to reprogram
the device. A logic-low on the SEL_CD pin selects the control bits with a "C1" or "D1" notation, per Table 3. A logic-high on the
SEL_CD pin selects the control bits with "C2" or "D2" notation, per Table 3.
Note that changing between two running frequencies using the SEL_CD pin may produce glitches in the output, especially if the post-
divider(s) is/are altered.
4.2 Power-Down and Output Enable
A logic-high on the PD pin powers down only those portions of the FS6377 which have their respective power-down control bits
enabled. Note that the PD pin has an internal pull-up.
When a post divider is powered down, the associated output driver is forced low. When all PLLs and post dividers are powered down
the crystal oscillator is also powered down. The XIN pin is forced low, and the XOUT pin is pulled high.
A logic-low on the OE pin tristates all output clocks. Note that this pin has an internal pull-up.
Rev. 4 | Page 5 of 24 | www.onsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FS7145-02G-XTD | IC CLOCK GEN PLL PROG 16SSOP |
| FSA221UMX | IC SWITCH AUD USB DPDT 10-MLP |
| FSA8008AUMX | IC CONFIG SW/AUD JACK DET 10UMLP |
| FSA8008UMX | IC AUDIO JACK DETECTOR/SW 10UMLP |
| FSA8009UMX | IC AUDIO JACK DETECTOR/SW 10UMLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FS-662 | 功能描述:模块化系统 - SOM A9M2440 Module 32MB 10Mbps Ethernet RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| FS6713-20-07 | 制造商:Schaffner 功能描述: |
| FS6BNCU | 制造商:Belden Inc 功能描述:BNC CONNECTOR UNIVERSAL |
| FS6BNCU-R | 制造商:Belden Inc 功能描述:RF/COAX BNC PLUG STR CRIMP 75 OHM G |
| FS6BNCUS | 制造商:ICM CORP 功能描述:BNC Connector Nickel 6 Universal Splice |
发布紧急采购，3分钟左右您将得到回复。