- 您现在的位置：买卖IC网 > PDF目录1809 > IR3522MTRPBF (International Rectifier)IC CTRL XPHASE3 DDR/VVT 32-MLPQ PDF资料下载
参数资料
| 型号： | IR3522MTRPBF |
| 厂商： | International Rectifier |
| 文件页数： | 14/32页 |
| 文件大小： | 0K |
| 描述： | IC CTRL XPHASE3 DDR/VVT 32-MLPQ |
| 标准包装： | 3,000 |
| 系列： | XPhase3™ |
| 应用： | 处理器 |
| 电流 - 电源： | 7mA |
| 电源电压： | 4.75 V ~ 7.5 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-MLPQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
IR3522
Serial VID Control
The IR3522 outputs can be controlled via a serial VID Interface (SVID) which employs a Fast Mode I 2 C protocol.
VREF1, which is the reference for VOUT1, can also be programmed to boot-up to one of four codes through pins
VID0 and VID1 prior to ENABLE rising if SVID communication is not available prior to power-up. Refer to Table 4.
Pins VID0 and VID1 have internal 100K pull-up resistors to an internal 3.3V. The SVID controls both the VOUT1
and VOUT2 margining (see Table 2 or 3) depending on which serial address precedes the data string. See Table 1
for proper address codes. If the top address is used, then both outputs will coincide with the values in Table 2
depending on data code used, where VOUT2 is always half the value of VOUT1. The second address will only
have an effect on VOUT2’s amplitude (margining +26.67 % and -25 %) as defined in Table 3. Since there is no
internal compensation for Vref_track (VOUT2 reference), It is recommended that VOUT2 be incremented to its
final value to prevent possible output overshoot. If no serial command is received before an enable event (ENABLE
pin going high), the controller’s VOUT1 will startup in a default state as indicated in Table 4 and VOUT2 to 0.75 V
(half of VDAC).
Addresses and data are serially transmitted in 8-bit words. The first data bit of the SVID data word represents the
PSI_L bit and will be ignored by the IR3522 therefore this system will never enter a power-saving mode. The
remaining data bits SVID[6:0] select the desired VOUTx regulation voltage as defined in Table 2 or Table 3
depending address chosen. VOUT1 is divided in half by an internal resistor divider to provide a reference voltage
(Vref_track) for VOUT2. This allows VOUT2 to track VOUT1 maintaining a desired differential voltage. SVID [6:0]
are the inputs to the Digital-to-Analog Converter (VREF) which then provides an analog reference voltage to the
transconductance type buffer amplifier. This VREF buffer provides a system reference on the VREF1 pin. The
VREF1 voltage along with error amplifier and remote sense differential amplifier input offsets are post-package
trimmed to provide a 0.5% system set-point accuracy, as measured in Figures 2A and 2B. VREF1 slew rates are
programmable by properly selecting external series RC compensation networks located between the VREF1 and
the LGND pins. The VREF1 source and sink currents are derived off the external oscillator frequency setting
resistor, R ROSC . The programmable slew rate enables the IR3522 to smoothly transition the regulated output
voltage throughout VID transitions resulting in a power supply input and output capacitor inrush currents, along with
output voltage overshoot, to be well controlled.
The ADDR1 and ADDR2 pins (5, 6) are reserved for controller addressing. These pins have internal 100K pull-up
resistors to an internal 3.3V. By floating or shorting to ground these two pins, four different controller identification
address states can be made. By setting bit 2 and 3 of the SVI address codes (see Figure 8) to the desired controller
address, a CPU can communicate with one controller while ignoring other controllers sharing the same SVID bus.
SVI Address [6:0] + Wr
6 5 4 ADDR1
ADDR2
1
0
WR
Figure 8 Bit 2 and 3 are use for Controller addressing
The SCL and SDA pins require external pull-up biasing and should not be floated. Biasing of pins SDA, SCL, VID0,
VID1, ADDR1 and ADDR2 prior to applying VCCL is acceptable. For Write, WR=0.
SVI Address
SVI Address [6:0] + Wr
[bit6 :bit5 : bit4 : ADDR1 _ ADDR2 : bit1 : bit0 : WR]
110 1_1 100 in binary or D_C in hex if ADDR1 and ADDR2 pins are high
110 1_1 010 in binary or D_A in hex if ADDR1 and ADDR2 pins are high
BOLD indicates the pin states of ADDR1 and ADDR2, in this case high or floating.
Table 1 – SVI Address
Page 14
Description
Set VID only Output 1
Set VID only Output 2
V3.01
相关PDF资料 |
PDF描述 |
|---|---|
| IR3523MTRPBF | IC XPHASE3 CTLR VR11.1 40-MLPQ |
| IR3527MTRPBF | IC CTRL XPHASE3 DUAL 24-MLPQ |
| IR3529MTRPBF | IC CTRL XPHASE CPU/ASIC 20-MLPQ |
| IR3550MTRPBF | IC DRIVER GATE 60A PQFN |
| IR3553MTRPBF | IC DRIVER GATE 40A PQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR3523 | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM DUAL OUTPUT CONTROL IC |
| IR3523MPBF | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM DUAL OUTPUT CONTROL IC |
| IR3523MTRPBF | 功能描述:开关变换器、稳压器与控制器 X-PHASE IR3523 AMD SVID CTRL IC RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IR3527 | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM DUAL PHASE IC |
| IR3527MPBF | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM DUAL PHASE IC |
发布紧急采购，3分钟左右您将得到回复。