- 您现在的位置：买卖IC网 > PDF目录381957 > ISL12029 (Intersil Corporation) Real Time Clock/Calendar with EEPROM(带EEPROM实时时钟/日历) PDF资料下载
参数资料
| 型号： | ISL12029 |
| 厂商： | Intersil Corporation |
| 英文描述： | Real Time Clock/Calendar with EEPROM(带EEPROM实时时钟/日历) |
| 中文描述： | 实时时钟/日历带有EEPROM（带EEPROM的实时时钟/日历） |
| 文件页数： | 9/28页 |
| 文件大小： | 426K |
| 代理商： | ISL12029 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
9
FN6206.6
October 18, 2006
Description
The ISL12029 device is a Real Time Clock with clock/calendar,
two polled alarms with integrated 512x8 EEPROM, oscillator
compensation, CPU Supervisor (Power-on Reset, Low Voltage
Sensing and Watchdog Timer) and battery backup switch.
The oscillator uses an external, low-cost 32.768kHz crystal.
All compensation and trim components are integrated on the
chip. This eliminates several external discrete components
and a trim capacitor, saving board area and component cost.
The Real-Time Clock keeps track of time with separate
registers for Hours, Minutes, Seconds. The Calendar has
separate registers for Date, Month, Year and Day-of-week.
The calendar is correct through 2099, with automatic leap
year correction.
The Dual Alarms can be set to any Clock/Calendar value for a
match. For instance, every minute, every Tuesday, or 5:23 AM
on March 21. The alarms can be polled in the Status Register
or can provide a hardware interrupt (IRQ/F
OUT
Pin). There is a
repeat mode for the alarms allowing a periodic interrupt.
The IRQ/F
OUT
pin may be software selected to provide a
frequency output of 1Hz, 4096Hz, or 32,768Hz or inactive.
The ISL12029 device integrates CPU Supervisory functions
(POR, WDT) and Battery Switch. There is Power-On-Reset
(RESET) output with 250ms delay from power-on when the
VDD supply crosses the V
RESET
threshold for the device. It will
also assert RESET when V
DD
goes below the specified
V
RESET
threshold for the device. The V
RESET
threshold is
selectable via VTS2/VTS1/VTS0 registers to five (5)
preselected levels. Their is WatchDog Timer (WDT) with 3
selectable time-out periods (0.25s, 0.75s and 1.75s) and
disabled setting. The WatchDog Timer activates the RESET pin
when it expires. Normally, the I
2
C Interface is disabled when the
RESET output is active, but this can be changed by using a
register bit to enable I
2
C operation in battery backup mode.
The device offers a backup power input pin. This V
BAT
pin
allows the device to be backed up by battery or SuperCap. The
entire ISL12029 device is fully operational from 2.7 to 5.5V and
the clock/calendar portion of the ISL12029 device remains fully
operational down to 1.8V (Standby Mode).
The ISL12029 device provides 4K bits of EEPROM with 8
modes of BlockLock control. The BlockLock allows a safe,
secure memory for critical user and configuration data, while
allowing a large user storage area.
Pin Descriptions
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the
device. The input buffer on this pin is always active (not
gated). The pull-up resistor on this pin must use the same
voltage source as V
DD
.
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and out
of the device. It has an open drain output and may be wire
ORed with other open drain or open collector outputs. The
input buffer is always active (not gated).
This open drain output requires the use of a pull-up resistor.
The pull-up resistor on this pin must use the same voltage
source as V
DD
. The output circuitry controls the fall time of the
output signal with the use of a slope controlled pull-down. The
circuit is designed for 400kHz I
2
C interface speed.
V
BAT
This input provides a backup supply voltage to the device.
V
BAT
supplies power to the device in the event the V
DD
supply fails. This pin can be connected to a battery, a
SuperCap or tied to ground if not used.
IRQ/F
OUT
(Interrupt Output/Frequency Output)
This dual function pin can be used as an interrupt or
frequency output pin. The IRQ/F
OUT
mode is selected via
the frequency out control bits of the control/status register.
Interrupt Mode.
The pin provides an interrupt signal
output. This signal notifies a host processor that an alarm
has occurred and requests action. It is an open drain
active low output.
Frequency Output Mode.
The pin outputs a clock signal
which is related to the crystal frequency. The frequency
output is user selectable and enabled via the I
2
C bus. It is
an open drain output.
The IRQ/F
OUT
pin is an open drain output requiring a pull-up
resistor which was intended to be used for clocking
applications for micro controllers. Choose the pull-up resistor
with care, since low values will cause high currents to flow in
the V
DD
and ground traces around the device which can
contribute to faulty oscillator function. For a 32kHz output,
values up to 10k
can be used with some degradation of the
square waveform.
RESET
The RESET signal output can be used to notify a host
processor that the watchdog timer has expired or the VDD
voltage supply has dipped below the V
RESET
threshold. It is
an open drain, active LOW output. Recommended value for
the pull-up resistor is 10k
. If unused it can be tied to
ground.
X1, X2
The X1 and X2 pins are the input and output, respectively, of
an inverting amplifier. An external 32.768kHz quartz crystal is
used with the ISL12029 to supply a timebase for the real time
clock. Internal compensation circuitry provides high accuracy
over the operating temperature range from -40°C to +85°C.
This oscillator compensation network can be used to calibrate
the crystal timing accuracy over temperature either during
manufacturing or with an external temperature sensor and
ISL12029
相关PDF资料 |
PDF描述 |
|---|---|
| ISL21032 | Precision 0.600V Low Voltage FGA References(精密0.600V低压FGA基准) |
| ISL28271 | Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifier(双微功率,单电源,轨对轨输入/输出(RRIO)测量放大器) |
| ISL28272 | Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifier(双微功率,单电源,轨对轨输入/输出(RRIO)测量放大器) |
| ISL28278 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Op-Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)运放) |
| ISL28478 | Dual and Quad Micropower Single Supply Rail-to-Rail Input and Output (RRIO) Op-Amp(双/四通道，微功率，单电源，轨对轨输入/输出(RRIO)运放) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL12029_10 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock/Calendar with I2C Busa?￠ and EEPROM |
| ISL12029_1012 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock/Calendar with I2C Bus? and EEPROM |
| ISL12029A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock/Calendar with I2C Bus? and EEPROM |
| ISL12029AIB27Z | 功能描述:实时时钟 REAL TIME CLKRTC W/ EPROM 2 63VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL12029AIB27Z-T | 功能描述:实时时钟 REAL TIME CLKRTC W/ EPROM 2 63VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。