- 您现在的位置：买卖IC网 > PDF目录20668 > ISL6236EVAL2 (Intersil)EVAL BOARD 2 FOR ISL6236 PDF资料下载
参数资料
| 型号： | ISL6236EVAL2 |
| 厂商： | Intersil |
| 文件页数： | 30/35页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD 2 FOR ISL6236 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页
ISL6236
TABLE 4. SHUTDOWN AND STANDBY CONTROL LOGIS
VEN LDO
Low
“>2.5” → High
“>2.5” → High
“>2.5” → High
“>2.5” → High
“>2.5” → High
“>2.5” → High
VEN1 (V)
Low
Low
High
High
Low
High
REF
VEN2 (V)
Low
Low
High
Low
High
REF
High
LDO
Off
On
On
On
On
On
On
SMPS1
Off
Off
On
On
Off
On
On (after SMPS2 is up)
SMPS2
Off
Off
On
Off
On
On (after SMPS1 is up)
On
R 1 = R 2 ? ? ------------------- – 1 ?
? V FB1 ?
Adjustable-Output Feedback (Dual-Mode FB)
Connect FB1 to GND to enable the fixed 5V or tie FB1 to
VCC to set the fixed 1.5V output. Connect a resistive
voltage-divider at FB1 between OUT1 and GND to adjust the
respective output voltage between 0.7V and 5.5V
(Figure 76). Choose R 2 to be approximately 10k and solve
for R 1 using Equation 6.
? V OUT1 ?
(EQ. 6)
where V FB1 = 0.7V nominal.
Likewise, connect REFIN2 to VCC to enable the fixed 3.3V
or tie REFIN2 to VREF3 to set the fixed 1.05V output. Set
the selection of input capacitors, MOSFETs and other
critical heat-contributing components.
3. Switching Frequency. This choice determines the basic
trade-off between size and efficiency. The optimal
frequency is largely a function of maximum input voltage
and MOSFET switching losses.
4. Inductor Ripple Current Ratio (LIR). LIR is the ratio of
the peak-peak ripple current to the average inductor
current. Size and efficiency trade-offs must be
considered when setting the inductor ripple current ratio.
Low inductor values cause large ripple currents, resulting
in the smallest size, but poor efficiency and high output
noise. Also, total output ripple above 3.5% of the output
regulation will cause the controller to trigger out-of-bound
condition. The minimum practical inductor value is one
R 3 = R 4 ? ? ------------------- – 1 ?
? V ?
REFIN2 from 0V to 2.50V for SMPS2 tracking mode
(Figure 77).
VR
OUT2
where:
? VR = 2V nominal (if tied to REF)
or
? VR = 3.3V nominal (if tied to VREF3)
Design Procedure
(EQ. 7)
that causes the circuit to operate at critical conduction
(where the inductor current just touches zero with every
cycle at maximum load). Inductor values lower than this
grant no further size-reduction benefit.
The ISL6236 pulse-skipping algorithm (SKIP = GND)
initiates skip mode at the critical conduction point, so the
inductor's operating point also determines the load
current at which PWM/PFM switchover occurs. The
optimum LIR point is usually found between 25% and
50% ripple current.
V IN
Establish the input voltage range and maximum load current
before choosing an inductor and its associated ripple current
ratio (LIR). The following four factors dictate the rest of the
design:
1. Input Voltage Range. The maximum value (V IN(MAX) )
must accommodate the maximum AC adapter voltage.
The minimum value (V IN(MIN) ) must account for the
lowest input voltage after drops due to connectors, fuses
and battery selector switches. Lower input voltages result
UGATE1
ISL6236
LGATE1
OUT1
Q3
Q4
R1
OUT1
in better efficiency.
2. Maximum Load Current. The peak load current
(I LOAD(MAX) ) determines the instantaneous component
stress and filtering requirements and thus drives output
capacitor selection, inductor saturation rating and the
design of the current-limit circuit. The continuous load
current (I LOAD ) determines the thermal stress and drives
30
FB1
R2
FIGURE 76. SETTING V OUT1 WITH A RESISTOR DIVIDER
FN6373.6
April 29, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BN2-EU-F1 | CONVERTER MOD DC/DC 15V 200W |
| ISL6605CBZA-T | IC MOSFET DRVR SYNC BUCK 8-SOIC |
| ACB70DHLD | CONN EDGECARD 140PS .050 DIP SLD |
| TC1303A-PP3EUN | IC REG DL BCK/LINEAR SYNC 10MSOP |
| M7WXK-0910J | D-SUB CABLE - MFU09K/MC10G/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6236IRZA | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6236IRZAR5281 | 功能描述:IC MAIN PWR CTRLR QUAD 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6236IRZA-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6236IRZA-TKR5281 | 功能描述:IC QUAD OUT POWER CONTROL 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6236IRZA-TR5281 | 功能描述:IC MAIN PWR CTRLR QUAD 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。