- 您现在的位置：买卖IC网 > PDF目录15167 > ISL6244HRZ-T (Intersil)IC REG CTRLR BUCK PWM 32-QFN PDF资料下载
参数资料
| 型号： | ISL6244HRZ-T |
| 厂商： | Intersil |
| 文件页数： | 11/25页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 32-QFN |
| 标准包装： | 6,000 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 4 |
| 频率 - 最大： | 4MHz |
| 占空比： | 75% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -10°C ~ 100°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6244
PWM Operation
The timing of each converter leg is set by the number of
active channels. The default channel setting for the ISL6244
is four. One switching cycle is defined as the time between
PWM1 pulse termination signals. The pulse termination
signal is an internally generated clock signal which triggers
the falling edge of PWM1. The cycle time of the pulse
termination signal is the inverse of the switching frequency
If R DS(ON) sensing is not desired, an independent current-
sense resistor in series with the lower MOSFET source can
serve as a sense element. The circuitry shown in Figure 15
represents channel n of an N-channel converter. This
circuitry is repeated for each channel in the converter, but
may not be active depending upon the status of the PWM3
and PWM4 pins as described in the previous section.
set by the resistor between the FS pin and ground. Each
cycle begins when the clock signal commands the channel-1
PWM output to go low. The PWM1 transition signals the
channel-1 MOSFET driver to turn off the channel-1 upper
I n
I
R
r DS ( ON )
SEN = I L --------------------------
ISEN
V IN
CHANNEL N
UPPER MOSFET
MOSFET and turn on the channel-1 synchronous MOSFET.
In the default channel configuration, the PWM2 pulse
SAMPLE
I L
terminates 1/4 of a cycle after PWM1. The PWM 3 output
follows another 1/4 of a cycle after PWM2. PWM4 terminates
another 1/4 of a cycle after PWM3.
If PWM3 is connected to VCC, then two channel operation is
selected and the PWM2 pulse terminates 1/2 of a cycle later.
&
HOLD
-
+
ISEN(n)
R ISEN
CHANNEL N
-
+
I L r DS ( ON )
Connecting PWM4 to VCC selects three channel operation and
LOWER MOSFET
the pulse-termination times are spaced in 1/3 cycle increments.
Once a PWM signal transitions low, it is held low for a
ISL6244 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
minimum of 1/4 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time
expires, the PWM output is enabled. The PWM output state
is driven by the position of the error amplifier output signal,
V COMP , minus the current correction signal relative to the
sawtooth ramp as illustrated in Figure 1. When the modified
V COMP voltage crosses the sawtooth ramp, the PWM output
transitions high. The MOSFET driver detects the change in
state of the PWM signal and turns off the synchronous
MOSFET and turns on the upper MOSFET. The PWM signal
will remain high until the pulse termination signal marks the
beginning of the next cycle by triggering the PWM signal low.
FIGURE 15. INTERNAL AND EXTERNAL CURRENT-SENSING
CIRCUITRY
Channel-Current Balance
The sampled current, I n , from each active channel is used to
gauge both overall load current and the relative channel
current carried in each leg of the converter. The individual
sample currents are summed and divided by the number of
active channels. The resulting average current, I AVG ,
provides a measure of the total load current demand on the
converter and the appropriate level of channel current. Using
Figures 15 and 16, the average current is defined as:
I AVG = ----------------------------------
Current Sensing
During the forced off time following a PWM transition low, the
I 1 + I 2 + … I N
N
(EQ. 4)
I AVG = ------------- ---------------------- )
R ISEN
controller senses channel load current by sampling the
voltage across the lower MOSFET r DS(ON) , see Figure 15. A
ground-referenced amplifier, internal to the ISL6244,
connects to the PHASE node through a resistor, R ISEN . The
voltage across R ISEN is equivalent to the voltage drop
across the R DS(ON) of the lower MOSFET while it is
conducting. The resulting current into the ISEN pin is
proportional to the channel current, I L . The ISEN current is
then sampled and held after sufficient settling time every
switching cycle. The sampled current, I n , is used for
channel-current balance, load-line regulation and
overcurrent protection. From Figure 15, the following
equation for I n is derived
I OUT r DS ( ON
N
where N is the number of active channels and I OUT is the
total load current.
The average current is then subtracted from the individual
channel sample currents. The resulting error current, I ER , is
then filtered before it adjusts V COMP . The modified V COMP
signal is compared to a sawtooth ramp signal and produces
a pulse width which corrects for any imbalance and drives
the error current toward zero. Figure 16 illustrates Intersil’s
patented current-balance method as implemented on
I n = I L ---------------------- )
r DS ( ON
R ISEN
where I L is the channel current.
11
(EQ. 3)
channel-1 of a multi-phase converter.
FN9106.3
December 28, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2TK-EY-F2 | CONVERTER MOD DC/DC 40V 50W |
| VE-2TJ-EY-F4 | CONVERTER MOD DC/DC 36V 50W |
| ISL6316CRZ | IC REG CTRLR BUCK PWM VM 40-QFN |
| ESC30DREN | CONN EDGECARD 60POS .100 EYELET |
| SLP392M050A7P3 | CAP ALUM 3900UF 50V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6246C WAF | 制造商:Intersil Corporation 功能描述: |
| ISL6247 6248 WAF | 制造商:Intersil Corporation 功能描述: |
| ISL6247ACR-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:Intersil Corporation 功能描述: |
| ISL6247CR | 功能描述:IC REG CTRLR PWM 40-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6247CR-T | 功能描述:IC REG CTRLR PWM 40-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。