- 您现在的位置：买卖IC网 > PDF目录15167 > ISL6244HRZ-T (Intersil)IC REG CTRLR BUCK PWM 32-QFN PDF资料下载
参数资料
| 型号： | ISL6244HRZ-T |
| 厂商： | Intersil |
| 文件页数： | 16/25页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 32-QFN |
| 标准包装： | 6,000 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 4 |
| 频率 - 最大： | 4MHz |
| 占空比： | 75% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -10°C ~ 100°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6244
If the ISL6244 is disabled during operation, the PGOOD
VOUT, 500mV/DIV
signal will not pull low until the output voltage decays below
the UV threshold.
PGOOD
UV
EN, 5V/DIV
+
350mV
-
POR
CIRCUIT
OC
-
+
85 μ A
I CHx
DAC
REFERENCE
t DELAY t RAMP1
t RAMP2
1ms/DIV
FIGURE 22. SOFT-START WAVEFORMS FOR ISL6244 BASED
VDIFF
+
OV
MULTI-PHASE BUCK CONVERTER
NOTE: Switching frequency 500kHz and R FB = 2.67k ?.
Fault Monitoring and Protection
The ISL6244 actively monitors voltage and current feedback
to detect fault conditions. Fault monitors trigger protective
measures to prevent damage to a microprocessor load. One
common power good indication signal is provided for linking
to external system monitors. The schematic in Figure 23
outlines the interaction between the fault monitors and the
power good signal.
Power Good Signal
The power good pin (PGOOD) is an open-drain logic output
which indicates that the converter is operating properly and
the output voltage is within a set window. The under-voltage
(UV) and over-voltage (OV) comparators create the output
voltage window. The controller also takes advantage of
current feedback to detect output over-current (OC)
conditions. PGOOD pulls low during shutdown and releases
high during soft-start once the output voltage reaches the
DAC level. Once high, PGOOD will only transition low when
the controller is disabled or a fault condition is detected. It
will return high under certain circumstances once a fault
clears.
Under-Voltage Protection
The voltage on V DIFF is internally offset by 350mV before it
is compared with the DAC reference voltage. By positively
offsetting the output voltage, an UV threshold is created
which moves relative to the VID code. During soft-start, the
slow rising output voltage eventually exceeds the UV
threshold. If a fault condition arises during operation and the
output voltage drops below the UV threshold, PGOOD will
immediately pull low, but converter operation will continue.
PGOOD will return high once the output voltage again
reaches regulation.
16
-
2.2V
FIGURE 23. POWER GOOD AND PROTECTION CIRCUITRY
Over-Voltage Protection
When the output of the differential amplifier (VDIFF) reaches
2.2V, PGOOD immediately goes low indicating a fault. Two
protective actions are taken by the ISL6244 to protect the
microprocessor load.
All PWM outputs are commanded low, directing the Intersil
drivers to turn on the lower MOSFETs. This shunts the
output to ground preventing any further increase in output
voltage. The PWM outputs remain low until VDIFF falls to the
programmed DAC level at which time they go into a high-
impedance state. The Intersil drivers respond by turning off
both upper and lower MOSFETs. If the over-voltage
condition recurs, the ISL6244 will again command the lower
MOSFETs to turn on. The ISL6244 will continue to protect
the load in this fashion as long as the over-voltage repeats.
Once an over-voltage condition is detected, normal PWM
operation ceases and PGOOD remains low until the
ISL6244 is reset. Cycling the voltage on EN below 1.23V or
the bias to VCC below the POR-falling threshold will reset
the controller.
Over-Current Protection
The ISL6244 monitors individual channel current to detect an
over-current condition. Each channel current is continually
compared with a constant 85 μ A reference current. Once any
of the currents exceeds the reference current, the comparator
triggers the converter to shutdown. The POR circuit places all
PWM signals in a high-impedance state which commands the
drivers to turn off both upper and lower MOSFETs. PGOOD
pulls low and the system remains in this state while the
controller counts 2048 phase clock cycles. This is followed by
a soft-start attempt (see Soft-Start ).
FN9106.3
December 28, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2TK-EY-F2 | CONVERTER MOD DC/DC 40V 50W |
| VE-2TJ-EY-F4 | CONVERTER MOD DC/DC 36V 50W |
| ISL6316CRZ | IC REG CTRLR BUCK PWM VM 40-QFN |
| ESC30DREN | CONN EDGECARD 60POS .100 EYELET |
| SLP392M050A7P3 | CAP ALUM 3900UF 50V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6246C WAF | 制造商:Intersil Corporation 功能描述: |
| ISL6247 6248 WAF | 制造商:Intersil Corporation 功能描述: |
| ISL6247ACR-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:Intersil Corporation 功能描述: |
| ISL6247CR | 功能描述:IC REG CTRLR PWM 40-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6247CR-T | 功能描述:IC REG CTRLR PWM 40-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。