参数资料
| 型号： | ISL62771IRTZ |
| 厂商： | Intersil |
| 文件页数： | 27/36页 |
| 文件大小： | 0K |
| 描述： | IC PWM CTRLR MULTIPHASE 40TQFN |
| 标准包装： | 60 |
| 系列： | Robust Ripple Regulator™ (R³) |
| 应用： | 控制器，AMD Fusion? SVI 2.0 CPU GPU |
| 输入电压： | 4.5 V ~ 25 V |
| 输出数： | 2 |
| 输出电压： | 0.006 V ~ 1.55 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ISL62771
ω sns = --------------------------------------------------------
R ntcnet × ---------------
------------------------------------------ × C n
R ntcnet + ---------------
Key Component Selection
Inductor DCR Current-Sensing Network
PHASE1 PHASE2
R SUM
1
R sum
N
R sum
N
where N is the number of phases.
(EQ. 17)
R SUM
I SUM+
Transfer function A cs (s) always has unity gain at DC. The inductor
DCR value increases as the winding temperature increases,
L
DCR
L
DCR
R NTCS
R NTC
R P
+
CN VCN
-
giving higher reading of the inductor DC current. The NTC R ntc
value decrease as its temperature decreases. Proper selection of
R sum , R ntcs , R p and R ntc parameters ensures that V Cn
represents the inductor total DC current over the temperature
range of interest.
RI
I SUM-
There are many sets of parameters that can properly
V Cn ( s ) = ? ------------------------------------------ × ------------- ? × I o ( s ) × A cs ( s ) (EQ. 13)
? R sum ?
? R ntcnet + --------------- ?
R ntcnet = ---------------------------------------------------- (EQ. 14)
1 + -------
ω L
A cs ( s ) = -----------------------
1 + -------------
C n = ---------------------------------------------------------------
R ntcnet × ---------------
------------------------------------------ × DCR
R ntcnet + ---------------
R O
R O
I O
FIGURE 20. DCR CURRENT-SENSING NETWORK
Figure 20 shows the inductor DCR current-sensing network for a
2-phase solution. An inductor current flows through the DCR and
creates a voltage drop. Each inductor has two resistors in R sum
and R o connected to the pads to accurately sense the inductor
current by sensing the DCR voltage drop. The R sum and R o
resistors are connected in a summing network as shown, and feed
the total current information to the NTC network (consisting of
R ntcs , R ntc and R p ) and capacitor C n . R ntc is a negative
temperature coefficient (NTC) thermistor, used to temperature
compensate the inductor DCR change.
The inductor output side pads are electrically shorted in the
schematic but have some parasitic impedance in actual board
layout, which is why one cannot simply short them together for the
current-sensing summing network. It is recommended to use
1 Ω ~10 Ω R o to create quality signals. Since R o value is much
smaller than the rest of the current sensing circuit, the following
analysis ignores it.
The summed inductor current information is presented to the
capacitor C n . Equations 13 thru 17 describe the frequency
domain relationship between inductor total current I o (s) and C n
voltage V Cn (s):
? ?
? R ntcnet DCR ?
N
N
( R ntcs + R ntc ) × R p
R ntcs + R ntc + R p
s
(EQ. 15)
s
ω sns
temperature-compensate the DCR change. Since the NTC network
and the R sum resistors form a voltage divider, V cn is always a
fraction of the inductor DCR voltage. It is recommended to have a
higher ratio of V cn to the inductor DCR voltage so the droop circuit
has a higher signal level to work with.
A typical set of parameters that provide good temperature
compensation are: R sum = 3.65k Ω , R p = 11k Ω , R ntcs = 2.61k Ω
and R ntc = 10k Ω (ERT-J1VR103J). The NTC network parameters
may need to be fine tuned on actual boards. One can apply full
load DC current and record the output voltage reading
immediately; then record the output voltage reading again when
the board has reached the thermal steady state. A good NTC
network can limit the output voltage drift to within 2mV. It is
recommended to follow the Intersil evaluation board layout and
current sensing network parameters to minimize engineering
time.
V Cn (s) also needs to represent real-time I o (s) for the controller to
achieve good transient response. Transfer function A cs (s) has a
pole ω sns and a zero ω L . One needs to match ω L and ω sns so
A cs (s) is unity gain at all frequencies. By forcing ω L equal to ω sns
and solving for the solution, Equation 18 gives Cn value.
L (EQ. 18)
R sum
N
R sum
N
For example, given N = 2, R sum = 3.65k Ω , R p = 11k Ω ,
R ntcs = 2.61k Ω , R ntc = 10k Ω , DCR = 0.88m Ω and L = 0.36μH,
Equation 18 gives C n = 0.294μF.
Assuming the compensator design is correct, Figure 21 shows the
expected load transient response waveforms if C n is correctly
selected. When the load current I core has a square change, the
output voltage V core also has a square response.
If C n value is too large or too small, V Cn (s) does not accurately
represent real-time I o (s) and worsens the transient response.
Figure 22 shows the load transient response when C n is too
small. V core sags excessively upon load insertion and may create
a system failure. Figure 23 shows the transient response when
ω L = -------------
DCR
L
27
(EQ. 16)
C n is too large. V core is sluggish in drooping to its final value.
There is excessive overshoot if load insertion occurs during this
time, which may negatively affect the CPU reliability.
FN8321.2
September 12, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| ISL62773IRZ-T | IC PWM REG MULTIPH AMD 48-QFN |
| ISL6277HRZ | IC PWM REG MULTIPH AMD 48-QFN |
| ISL62870HRUZ-T | IC REG CTRLR BUCK PWM 16-TQFN |
| ISL62872HRUZ-T | IC REG CTRLR BUCK PWM 20-TQFN |
| ISL62873HRUZ-T | IC REG CTRLR BUCK PWM 16UTQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62771IRTZ-T | 功能描述:IC PWM CTRLR MULTIPHASE 40TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:Robust Ripple Regulator™ (R³) 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL62773 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multiphase PWM Regulator for AMD Fusiona?￠ Desktop CPUs Using SVI 2.0 |
| ISL62773HRZ | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLR FOR AMD FUSION UP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL62773HRZ-T | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLR FOR AMD FUSION UP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL62773IRZ | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLR FOR AMD FUSION UP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。