参数资料
| 型号： | ISL6333IRZ |
| 厂商： | Intersil |
| 文件页数： | 36/40页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 3PHASE BUCK 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，Intel VR11 |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 1.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页
ISL6333, ISL6333A, ISL6333B, ISL6333C
pulsating voltage at the phase nodes. The output filter also
must provide the transient energy until the regulator can
respond. Because it has a low bandwidth compared to the
switching frequency, the output filter limits the system
transient response. The output capacitors must supply or
sink load current while the current in the output inductors
increases or decreases to meet the demand.
In high-speed converters, the output capacitor bank is usually
the most costly (and often the largest) part of the circuit.
Output filter design begins with minimizing the cost of this part
of the circuit. The critical load parameters in choosing the
output capacitors are the maximum size of the load step, Δ I,
the load-current slew rate, di/dt, and the maximum allowable
The output inductors must be capable of assuming the entire
load current before the output voltage decreases more than
Δ V MAX . This places an upper limit on inductance.
Equation 44 gives the upper limit on L for the cases when
the trailing edge of the current transient causes a greater
output-voltage deviation than the leading edge. Equation 45
addresses the leading edge. Normally, the trailing edge
dictates the selection of L because duty cycles are usually
less than 50%. Nevertheless, both inequalities should be
evaluated, and L should be selected based on the lower of
the two results. In each equation, L is the per-channel
inductance, C is the total output capacitance, and N is the
number of active channels.
L ≤ --------------------------------- ? Δ V MAX – ( Δ I ? ESR )
L ≤ ----------------------------- ? Δ V MAX – ( Δ I ? ESR ) ? ? V IN – V O ?
( Δ I ) 2
output-voltage deviation under transient loading, Δ V MAX .
Capacitors are characterized according to their capacitance,
ESR, and ESL (equivalent series inductance).
At the beginning of the load transient, the output capacitors
supply all of the transient current. The output voltage will
2 ? N ? C ? V O
( Δ I ) 2
1.25 ? N ? C
? ?
(EQ. 44)
(EQ. 45)
initially deviate by an amount approximated by the voltage
drop across the ESL. As the load current increases, the
voltage drop across the ESR increases linearly until the load
current reaches its final value. The capacitors selected must
have sufficiently low ESL and ESR so that the total
output-voltage deviation is less than the allowable maximum.
Neglecting the contribution of inductor current and regulator
response, the output voltage initially deviates by an amount
as shown in Equation 42.
Switching Frequency
There are a number of variables to consider when choosing
the switching frequency, as there are considerable effects on
the upper MOSFET loss calculation. These effects are
frequency. The lower limit is established by the requirement
for fast transient response and small output-voltage ripple.
Choose the lowest switching frequency that allows the
Δ V ≈ ESL ? ----- + ESR ? Δ I
di
dt
(EQ. 42)
regulator to meet the transient-response requirements.
Switching frequency is determined by the selection of the
The filter capacitor must have sufficiently low ESL and ESR
so that Δ V < Δ V MAX .
Most capacitor solutions rely on a mixture of high frequency
capacitors with relatively low capacitance in combination
with bulk capacitors having high capacitance but limited
high-frequency performance. Minimizing the ESL of the
high-frequency capacitors allows them to support the output
voltage as the current increases. Minimizing the ESR of the
bulk capacitors allows them to supply the increased current
with less output voltage deviation.
The ESR of the bulk capacitors also creates the majority of the
output-voltage ripple. As the bulk capacitors sink and source
and Equation 2), a voltage develops across the bulk capacitor
frequency-setting resistor, R T . Figure 26 and Equation 46
are provided to assist in selecting the correct value for R T .
500
100
10
ESR equal to I C(P-P) (ESR). Thus, once the output capacitors
are selected, the maximum allowable ripple voltage, V P-
50k
100k 1M
SWITCHING FREQUENCY (Hz)
2M
P(MAX) , determines the lower limit on the inductance.
FIGURE 26. R T vs SWITCHING FREQUENCY
IN – N ? V OUT ? V OUT
? V ?
L ≥ ESR ? --------------------------------------------------------------------
? ?
f S ? V IN ? V P-P ( MAX )
(EQ. 43)
R T = 10
[ 10.61 – ( 1.035 ? log ( f S ) ) ]
(EQ. 46)
Since the capacitors are supplying a decreasing portion of
the load current while the regulator recovers from the
transient, the capacitor voltage becomes slightly depleted.
36
Input Capacitor Selection
The input capacitors are responsible for sourcing the AC
component of the input current flowing into the upper
MOSFETs. Their RMS current capacity must be sufficient
FN6520.3
October 8, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6334AIRZR5368 | IC CTRLR PWM 4PHASE BUCK 40QFN |
| ISL6334BIRZ-T | IC CTRLR PWM SYNC BUCK 40-QFN |
| ISL6334CRZ | IC CTRLR PWM 4PHASE BUCK 40-QFN |
| ISL6334DIRZ | IC CTRLR PWM 4PHASE VR11.1 40QFN |
| ISL6336BCRZ | IC CTRLR PWM SYNC BUCK 48-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6333IRZ-T | 功能描述:IC CTRLR PWM 3PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6334ACRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6334ACRZR5368 | 功能描述:IC CTRLR PWM 4PHASE BUCK 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6334ACRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6334ACRZ-TR5368 | 功能描述:IC CTRLR PWM 4PHASE BUCK 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。