参数资料
| 型号： | ISL6363IRTZ |
| 厂商： | Intersil |
| 文件页数： | 21/32页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER VR12 48TQFN |
| 标准包装： | 50 |
| 应用： | 控制器，Intel VR12 |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 2 |
| 输出电压： | 0.25 V ~ 1.52 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ISL6363
All the above fault conditions can be reset by bringing VR_ON low
or by bringing VCC below the POR threshold. When VR_ON and
VCC return to their high operating levels, a soft-start will occur
Table 5 summarizes the fault protections.
CONTROLLER IN
PS0/1 MODE
C2 R3
C1 R2
C3.1
CONTROLLER IN
PS2/3 MODE
C2 R3
C1 R2
C3.1
TABLE 5. FAULT PROTECTION SUMMARY
FAULT DURATION
VSEN
R1
C2.2 R3.2
FB
E/A
VSEN
COMP
R1
C2.2 R3.2
FB
E/A
COMP
BEFORE
FAULT
PSICOMP
PSICOMP
FAULT TYPE
Overcurrent
PROTECTION
120μs
PROTECTION ACTION RESET
PWM tri-state, PGOOD VR_ON
FIGURE 15. PSICOMP FUNCTION
Phase Current
Unbalance
Way-Overcurrent
(1.5xOC)
Overvoltage
+200mV
1ms
Immediately
latched low
PGOOD latched low.
Actively pulls the
output voltage to
toggle or
VCC toggle
When the PSICOMP switch is off, C2.2 and R3.2 are
disconnected from the FB pin. However, the controller still
actively drives the PSICOMP pin to allow for smooth transitions
between modes of operation.
The PSICOMP function ensures excellent transient response in
both PS0, PS1 and PS2/3 modes of operation. If the PSICOMP
function is not needed C2.2 and R3.2 can be disconnected.
below VID value, then
tri-state.
CURRENT MONITOR
The ISL6363 provides the current monitor function for both VRs.
IMON pin reports VR1 inductor current and IMONG pins reports
VR2 inductor current. Since they are designed following the same
principle, the following discussion will be only based on the IMON
pin but also applies to the IMONG pin.
The IMON pin outputs a high-speed analog current source that is
3 times of the droop current flowing out of the FB pin. Thus
becoming Equation 18:
I IMON = 3 × I droop (EQ. 18)
As the “Simplified Application Circuit” on page 6 shows, a
resistor R imon is connected to the IMON pin to convert the IMON
pin current to voltage. A capacitor can be paralleled with R imon
to filter the voltage information.
The IMON pin voltage range is 0V to 2.7V. The controller monitors
the IMON pin voltage and considers that VR1 has reached
ICCMAX on IMON pin voltage is 2.7V.
PSICOMP Function
Figure 15 shows the PSICOMP function. A switch turns on to
short the FB and the PSICOMP pins when the controller is in PS2
mode. The RC network C2.2 and R3.2 is connected in parallel
with R1 and C2/R3 compensation network in PS2/3 mode. This
Adaptive Body Diode Conduction Time
Reduction
In DCM, the controller turns off the low-side MOSFET when the
inductor current approaches zero. During on-time of the low-side
MOSFET, phase voltage is negative and the amount is the
MOSFET r DS(ON) voltage drop, which is proportional to the
inductor current. A phase comparator inside the controller
monitors the phase voltage during on-time of the low-side
MOSFET and compares it with a threshold to determine the
zero-crossing point of the inductor current. If the inductor current
has not reached zero when the low-side MOSFET turns off, it will
flow through the low-side MOSFET body diode, causing the phase
node to have a larger voltage drop until it decays to zero. If the
inductor current has crossed zero and reversed the direction when
the low-side MOSFET turns off, it will flow through the high-side
MOSFET body diode, causing the phase node to have a spike until
it decays to zero. The controller continues monitoring the phase
voltage after turning off the low-side MOSFET and adjusts the
phase comparator threshold voltage accordingly in iterative steps,
such that the low-side MOSFET body diode conducts for
approximately 40ns to minimize the body diode-related loss.
Supported Data and Configuration Registers
The controller supports the following data and configuration
registers.
TABLE 6. SUPPORTED DATA AND CONFIGURATION
REGISTERS
additional RC network increases the high frequency content of
the signal passing from the output voltage to the COMP pin which
will improve transient response in PS2/3 mode of operation.
INDEX
00h
REGISTER
NAME
Vendor ID
DESCRIPTION
Uniquely identifies the VR
DEFAULT
VALUE
12h
vendor. Assigned by Intel.
01h
Product ID
Uniquely identifies the VR
1Fh
product. Intersil assigns this
number.
21
02h
05h
Product
Revision
Protocol ID
Uniquely identifies the revision
of the VR control IC. Intersil
assigns this data.
Identifies what revision of SVID 01h
protocol the controller supports.
FN6898.1
September 5, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| RBM44DSES-S243 | CONN EDGECARD 88POS .156 EYELET |
| X40035S14I-AT1 | IC VOLTAGE MONITOR TRPL 14-SOIC |
| RSM22DSEI-S243 | CONN EDGECARD 44POS .156 EYELET |
| X40035S14I-A | IC VOLTAGE MONITOR TRPL 14-SOIC |
| ESM22DTBT-S189 | CONN EDGECARD 44POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6363IRTZ-T | 功能描述:IC CONTROLLER VR12 48TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6364ACRZ | 功能描述:IC CNTRLR DUAL IMVP7 VR12 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6364ACRZ-T | 功能描述:IC CNTRLR DUAL IMVP7 VR12 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6364AIRZ | 功能描述:IC CNTRLR DUAL IMVP7 VR12 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6364AIRZ-T | 功能描述:IC CNTRLR DUAL IMVP7 VR12 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。