- 您现在的位置：买卖IC网 > PDF目录20673 > ISL6754DBEVAL1Z (Intersil)BOARD DEMO FOR ISL6754 PDF资料下载
参数资料
| 型号： | ISL6754DBEVAL1Z |
| 厂商： | Intersil |
| 文件页数： | 12/19页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO FOR ISL6754 |
| 标准包装： | 1 |
| 系列： | * |
ISL6754
If voltage-mode control is used in a bridge topology, it should
be noted that peak current limit results in inherently unstable
operation. DC blocking capacitors used in voltage-mode
selected so that the ramp amplitude reaches 1.0V at
minimum input voltage within the duration of one half-cycle.
bridge topologies become unbalanced, as does the flux in
1
20
the transformer core. The average overcurrent circuitry
prevents this behavior by maintaining symmetric duty cycles
VIN
2
3
19
18
for each half-cycle. If the average current limit circuitry is not
used, a latching overcurrent shutdown method using
R3
4
5
ISL6754
17
16
external components is recommended.
The CS to output propagation delay is increased by the
leading edge blanking (LEB) interval. The effective delay is
the sum of the two delays and is 130ns maximum.
6
7
8 RAMP
9
15
14
13
12
Voltage Feed Forward Operation
C7
10
GND 11
Voltage feed forward is a technique used to regulate the
output voltage for changes in input voltage without the
intervention of the control loop. Voltage feed forward is
implemented in voltage-mode control loops, but is redundant
and unnecessary in peak current-mode control loops.
FIGURE 9. VOLTAGE FEED FORWARD CONTROL
Voltage feed forward operates by modulating the sawtooth
ramp in direct proportion to the input voltage. Figure 8
demonstrates the concept.
The charging time of the ramp capacitor is:
? V RAMP ( PEAK ) ?
t = – R3 ? C7 ? ln ? 1 – ---------------------------------------- ? S
? V IN ( MIN ) ?
(EQ. 7)
– 2.5 ? 10
R3 = ------------------------------------------------------------------------- = ------------------------------------------------------------
? ln ? 1 – ---------- ?
? V RAMP ( PEAK ) ? 1
4.7 ? 10
VIN
ERROR VOLTAGE
RAMP
CT
OUTLL, LR
For optimum performance, the maximum value of the
capacitor should be limited to 10nF. The maximum DC
current through the resistor should be limited to 2mA
maximum. For example, if the oscillator frequency is
400kHz, the minimum input voltage is 300V, and a 4.7nF
ramp capacitor is selected, the value of the resistor can be
determined by rearranging Equation 7.
– 6
– t
– 9
C7 ? ln ? 1 – ---------------------------------------- ? ? 300 ?
? V IN ( MIN ) ) ?
= 159
k Ω
(EQ. 8)
FIGURE 8. VOLTAGE FEED FORWARD BEHAVIOR
Input voltage feed forward may be implemented using the
RAMP input. An RC network connected between the input
voltage and ground, as shown in Figure 9, generates a
voltage ramp whose charging rate varies with the amplitude
of the source voltage. At the termination of the active output
pulse, RAMP is discharged to ground so that a repetitive
sawtooth waveform is created. The RAMP waveform is
compared to the VERR voltage to determine duty cycle. The
selection of the RC components depends upon the desired
input voltage operating range and the frequency of the
oscillator. In typical applications, the RC components are
12
where t is equal to the oscillator period minus the deadtime.
If the deadtime is short relative to the oscillator period, it can
be ignored for this calculation.
If feed forward operation is not desired, the RC network may
be connected to V REF rather than the input voltage.
Alternatively, a resistor divider from CTBUF may be used as
the sawtooth signal. Regardless, a sawtooth waveform must
be generated on RAMP as it is required for proper PWM
operation.
Gate Drive
The ISL6754 outputs are capable of sourcing and sinking
10mA (at rated VOH, VOL) and are intended to be used in
conjunction with integrated FET drivers or discrete bipolar
totem pole drivers. The typical on resistance of the outputs is
50 Ω .
FN6754.1
September 29, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| C0603C0G1E6R2D | CAP CER 6.2PF 25V NP0 0201 |
| VI-J63-CX-F4 | CONVERTER MOD DC/DC 24V 75W |
| ISL6612ACBZA-T | IC MOSFET DRVR SYNC BUCK 8-SOIC |
| TC1313-ZA0EUNTR | IC REG DL BCK/LINEAR SYNC 10MSOP |
| M7VXK-0906R | D-SUB CABLE - MMU09K/MC10M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6755AAZA | 功能描述:IC REG CTRLR PWM CM/VM 20-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6755AAZA-T | 功能描述:IC REG CTRLR PWM CM/VM 20-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6801AB | 功能描述:IC DRIVER HI-SIDE HI VOLT 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:低端 输入类型:非反相 延迟时间:40ns 电流 - 峰:9A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:4.5 V ~ 35 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263 包装:管件 |
| ISL6801ABT | 功能描述:IC DRIVER HISIDE BOOTSTRAP 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:低端 输入类型:非反相 延迟时间:40ns 电流 - 峰:9A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:4.5 V ~ 35 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263 包装:管件 |
| ISL6801ABTS2357 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。