参数资料
| 型号： | ISL78220ANEZ-T |
| 厂商： | Intersil |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | IC PWM CONTROLLER |
| 标准包装： | 1,000 |
| 系列： | * |
ISL78220
VIN
RSEN
L
VOUT
(= L/DCR), the voltage across the capacitor V C is equal to the
voltage drop across the DCR, i.e., proportional to the channel
current.
With the internal low-offset differential current sense amplifier,
ISEN
RSET
SENSE RESISTOR
CURRENT SENSING
the capacitor voltage V C is replicated across the sense resistor
R SET . Therefore the current flows into the ISENxP pin is
proportional to the inductor current. Equation 8 shows that the
ratio of the channel current to the sensed current I SEN is driven
by the value of the sense resistor and the DCR of the inductor.
I SEN = I L ? -------------
ISEN
CSA
ISEN(n)P
DCR
R SET
(EQ. 8)
ISL78220 INTERNAL CIRCUITS
ISEN(n)N
Light Load Efficiency
Enhancement Schemes
For switching mode power supplies, the total loss is related to
FIGURE 20. SENSE RESISTOR CURRENT SENSING
Inductor DCR Sensing
An inductor’s winding is characteristic of a distributed resistance
as measured by the DCR (Direct Current Resistance) parameter.
IL
both the conduction loss and the switching loss. At heavy load
the conduction loss is dominant while the switching loss will take
charge at light load condition. So, if a multiphase converter is
running at a fixed phase number for the entire load range, we will
observe that below a certain load point the total efficiency starts
to drop heavily. The ISL78220 has automatic phase dropping,
cycle-by-cycle diode emulation and pulse skipping features to
enhance the light load efficiency. By observing the total input
current on-the-fly and dropping the active phase numbers
VIN
DCR
C
L
R
VOUT
accordingly, the overall system can achieve optimized efficiency
over the entire load range. All the above mentioned light load
enhancement features can be disabled by simply pulling the
MODE pin to VCC.
ISEN
RSET
INDUCTOR DCR
CURRENT SENSING
Adjustable Automatic Phase
Dropping/Adding at Light Load Condition
If the MODE pin is connected to a resistor to GND, and the voltage
on the MODE pin is lower than its disable threshold 4V, the
ISEN
CSA
ISEN(n)P
adjustable automatic phase dropping/adding mode will be
enabled. When the ISL78220 controller works in this mode, it
ISEN(n)N
ISL78220 INTERNAL CIRCUITS
FIGURE 21. INDUCTOR DCR CURRENT SENSING
Consider the inductor DCR as a separate lumped quantity, as
shown in Figure 21. The channel current I L , flowing through the
inductor, will also pass through the DCR. Equation 6 shows the
S-domain equivalent voltage across the inductor V L .
will automatically adjust the active phase number by comparing
the V MODE and V IOUT , which represents sensed total current
information. The V MODE sets the overall phase dropping
threshold, and the V IOUT is proportional to the input current,
which is in turn proportional to the load current. The smaller the
load current, the lower the voltage observed on the IOUT pin, and
the ISL78220 will drop phases in operation. Once the MODE pin
voltage is fixed, the threshold to determine how many phases are
in operation is dependent on two factors:
1. The maximum configured phase number.
V L = I L ? ( s ? L + DCR )
(EQ. 6)
2. The voltage on the IOUT pin (V IOUT ).
? s ? ------------ + 1 ? ? ( DCR ? I )
V C = -----------------------------------------------------------------
A simple R-C network across the inductor extracts the DCR
voltage, as shown in Figure 21.
The voltage on the capacitor V C , can be shown to be proportional
to the channel current I L , see Equation 7.
L
? DCR ? L (EQ. 7)
( s ? RC + 1 )
If the R-C network components are selected such that the RC
time constant (= R*C) matches the inductor time constant
17
For example, if the converter is working in 6-phase operation and
the MODE pin is set to 1.2V, in this case the converter will
monitor the V IOUT and compare to 1.2V, such that when the
V IOUT is less than 800mV (66.6% of 1.2V), it will drop from
6-phase to 4-phase; if less than 600mV (50% of 1.2V), it will drop
to 3-phase; if less than 400mV (33% of 1.2V), it will drop to
2-phase. The detailed threshold setting is shown in the “Electrical
If PWM_TRI is tied to VCC, the dropped phase will provide a 2.5V
tri-level signal at its PWM output. The external driver has to
FN7688.3
December 24, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| ISL78225ANEZ-T | IC PWM CONTROLLER |
| ISL78228ARZ | IC REG BUCK SYNC ADJ DL 10-DFN |
| ISL78301FVEAZ | IC REG LDO 3.3V .15A 14HTSSOP |
| ISL78302AARBJZ | IC REG LDO 1.5V/2.8V .3A 10DFN |
| ISL78307FBECZ | IC REG LDO ADJ 50MA 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL78220ANZ-T | 制造商:Intersil Corporation 功能描述:AUTOMOTIVE GRADE 6-PHASE BOOST PWM CONTROLLER - 44LD TQFP PB - Tape and Reel |
| ISL78220EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL78220 EVALUATION BOARD 1 - 44 LEAD - TQFP - ROHS COMPLIAN - Bulk |
| ISL78223 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:ZVS Full-Bridge PWM Controller with Adjustable Synchronous Rectifier Control |
| ISL78223AAZ | 功能描述:电流型 PWM 控制器 ZVS Full Bridge PWM Controller Adj Rect. RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL78223AAZ-T | 制造商:Intersil Corporation 功能描述:ZVS FULL BRIDGE PWM CONTROLLER, 20LD QSOP, PB-FREE W/ ANNEAL - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG CTRLR PWM ISOLATED 20QSOP 制造商:Intersil 功能描述:ZVS Full Bridge PWM- Controller Adj Rect. |
发布紧急采购，3分钟左右您将得到回复。