参数资料
| 型号： | ISL78220ANEZ-T |
| 厂商： | Intersil |
| 文件页数： | 3/22页 |
| 文件大小： | 0K |
| 描述： | IC PWM CONTROLLER |
| 标准包装： | 1,000 |
| 系列： | * |
ISL78220
Functional Pin Description (Continued)
PIN #
12
13, 14, 15,
16, 17, 18
19
20
21, 22, 23,
24, 25, 26,
27, 28, 29,
30, 31, 32
33
34
35
36
37
38
39
40
41
42
43
44
SYMBOL
PWM_TRI
PWM1, PWM3, PWM5,
PWM2, PWM4, PWM6
DRIVE_EN
NC
ISEN1N, ISEN1P, ISEN3N,
ISEN3P, ISEN5N, ISEN5P,
ISEN2N, ISEN2P, ISEN4N,
ISEN4P, ISEN6N, ISEN6P
VIN
VCC
GND
MODE
IOUT
VIN_SEN
VIN_OVB
VOUT_SEN
VOUT_OVB
DMAX
EN
PGOOD
Exposed Pad
3
DESCRIPTION
This pin enables the tri-level of the PWM output signal. Pulling this pin to GND forces the PWM output to be
traditional two level logic. Pulling the PWM_TRI pin to VCC will enable tri level PWM signals, then PWM output can
be at the 2.5V tri level condition.
Pulse width modulation outputs. Connect these pins to the PWM input pins of the external driver ICs. The number
of active channels is determined by the state of PWM3, PWM4, PWM5 and PWM6. For 2-phase operation, connect
PWM3 to VCC; similarly, connect PWM4 to VCC for 3-phase, connect PWM5 or PWM6 to VCC for 4-phase
operation.
Driver enable output pin. This pin is connected to the enable pin of MOSFET drivers.
Not Connected – This pin is not electrically connected internally.
The ISENxP and ISENxN pins are current sense inputs to individual differential amplifiers. The sensed current is
used as a reference for current mode control and overcurrent protection. Inactive channels should have their
respective ISENxN pins connected to VIN and ISENxP pins left open or tied to VIN. The ISL78220 utilizes external
sense resistor current sensing method or Inductor DCR sensing method.
Connect input rail to this pin. This pin is connected to the internal linear regulator, generating the power necessary
to operate the chip. It is recommended the DC voltage applied to the VIN pin does not exceed 40V.
This pin is the output of the internal linear regulator that supplies the bias and gate voltage for the IC. A minimum
4.7μF decoupling ceramic capacitor should be connected from VCC to GND. The controller starts to operate when
the voltage on this pin exceeds the rising POR threshold and shuts down when the voltage on this pin drops below
the falling POR threshold. This pin can be connected directly to a +5V supply if VIN falls below 5.6V.
Bias and reference ground for the IC.
Mode selection pin. Pull this pin to logic HIGH for forced PWM mode; phase dropping/adding is inactive during
forced PWM mode. Connecting a resistor from MODE pin to GND will initialize phase dropping mode (PDM). In
PDM, a 5μA fixed reference current will flowing out of MODE pin, and the phase dropping threshold can be
programmed by adjusting the resistor value.
IOUT is the current monitor pin with an additional OCP adjustment function. An RC network needs to be placed
between IOUT and GND to ensure the proper operation. The voltage at the IOUT pin will be proportional to the input
current. If the voltage on the IOUT pin is higher than 2V, ISL78220 will go into overcurrent protection mode and
the chip will latch off until the EN pin is toggled.
The VIN_SEN pin is used for sensing the VIN voltage. A resistor divider network is connected between this pin and
boost power stage input voltage rail. When the voltage on VIN_SEN is greater than 2.4V, the VIN_OVB pin will be
pulled low to indicate an input overvoltage condition. The threshold voltage can be programmed by changing the
divider ratios.
The VIN_OVB pin is an open drain indicator of an overvoltage condition at the input. When the voltage on the
VIN_SEN pin is greater than the 2.4V threshold, the VIN_OVB pin will be pulled low.
The VOUT_SEN pin is used for sensing the output voltage, a resistor divider network is connected between this pin
and output voltage rail. When the voltage on VOUT_SEN pin is greater than 2.4V, VOUT_OVB pin will be pulled low,
indicating an output overvoltage condition.
The VOUT_OVB pin is an open drain indicator of an overvoltage condition at the output. When the voltage on the
VOUT_SEN pin is greater than the 2.4V threshold, the VOUT_OVB pin will be pulled low and latched, toggling VIN
or EN will reset the latch.
DMAX pin sets the maximum duty cycle of the PWM modulator. If the DMAX pin is connected to GND, the
maximum duty cycle will be set to 91.7%. Floating this pin will limit the duty cycle to 75% and connecting the
DMAX pin to VCC will limit the duty cycle to 83.3%.
This pin is a threshold-sensitive enable input for the controller. Connecting the power supply input to EN pin
through an appropriate resistor divider provides a means to synchronize power-up of the controller and the
MOSFET driver ICs. When EN pin is driven above 1.2V, the ISL78220 is active depending on status of the internal
POR, and pending fault states. Driving EN pin below 1.1V will clear all fault states and the ISL78220 will soft-start
when re-enabled.
This pin is used as an indication of the end of soft-start and output regulation. It is an open-drain logic output that
is low impedance until the soft-start is completed. It will be pulled low again once the UV/OV/OC/OT conditions
are detected.
It is recommended to solder the Exposed Pad to the ground plane.
FN7688.3
December 24, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| ISL78225ANEZ-T | IC PWM CONTROLLER |
| ISL78228ARZ | IC REG BUCK SYNC ADJ DL 10-DFN |
| ISL78301FVEAZ | IC REG LDO 3.3V .15A 14HTSSOP |
| ISL78302AARBJZ | IC REG LDO 1.5V/2.8V .3A 10DFN |
| ISL78307FBECZ | IC REG LDO ADJ 50MA 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL78220ANZ-T | 制造商:Intersil Corporation 功能描述:AUTOMOTIVE GRADE 6-PHASE BOOST PWM CONTROLLER - 44LD TQFP PB - Tape and Reel |
| ISL78220EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL78220 EVALUATION BOARD 1 - 44 LEAD - TQFP - ROHS COMPLIAN - Bulk |
| ISL78223 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:ZVS Full-Bridge PWM Controller with Adjustable Synchronous Rectifier Control |
| ISL78223AAZ | 功能描述:电流型 PWM 控制器 ZVS Full Bridge PWM Controller Adj Rect. RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL78223AAZ-T | 制造商:Intersil Corporation 功能描述:ZVS FULL BRIDGE PWM CONTROLLER, 20LD QSOP, PB-FREE W/ ANNEAL - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG CTRLR PWM ISOLATED 20QSOP 制造商:Intersil 功能描述:ZVS Full Bridge PWM- Controller Adj Rect. |
发布紧急采购，3分钟左右您将得到回复。