参数资料
| 型号： | ISL8101CRZ-T |
| 厂商： | Intersil |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM BUCK 2PHASE 24-QFN |
| 标准包装： | 6,000 |
| 应用： | 控制器，Intel VRM9，VRM10，AMD Hammer 应用 |
| 输入电压： | 4.6 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 2.3 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN（4x4） |
| 包装： | 带卷 (TR) |
ISL8101
At the beginning of the load transient, the output capacitors
supply all of the transient current. The output voltage will
initially deviate by an amount approximated by the voltage
drop across the ESL. As the load current increases, the
voltage drop across the ESR increases linearly until the load
current reaches its final value. The capacitors selected must
have sufficiently low ESL and ESR so that the total output-
voltage deviation is less than the allowable maximum.
Neglecting the contribution of inductor current and regulator
response, the output voltage initially deviates according to
Equation 21.
Normally, the trailing edge dictates the selection of L, since
duty cycles are usually less than 50%. Nevertheless, both
inequalities should be evaluated, and L should be selected
based on the lower of the two results. In all equations in this
paragraph, L is the per-channel inductance and C is the total
output bulk capacitance.
LAYOUT CONSIDERATIONS
MOSFETs switch very fast and efficiently. The speed with
which the current transitions from one device to another
causes voltage spikes across the interconnecting
Δ V ≈ ( ESL ) ----- + ( ESR ) Δ I
di
dt
(EQ. 21)
impedances and parasitic circuit elements. These voltage
spikes can degrade efficiency, radiate noise into the circuit
and lead to device overvoltage stress. Careful component
( V IN – 2 ? V OUT ) ? V OUT
L ≥ ESR ? -----------------------------------------------------------------
The filter capacitor must have sufficiently low ESL and ESR
so that Δ V < Δ V MAX .
Most capacitor solutions rely on a mixture of high-frequency
capacitors with relatively low capacitance in combination
with bulk capacitors having high capacitance but limited
high-frequency performance. Minimizing the ESL of the
high-frequency capacitors allows them to support the output
voltage as the current increases. Minimizing the ESR of the
bulk capacitors allows them to supply the increased current
with less output voltage deviation.
The ESR of the bulk capacitors is also responsible for the
majority of the output-voltage ripple. As the bulk capacitors
sink and source the inductor ac ripple current, a voltage
develops across the bulk-capacitor ESR equal to I P-P . Thus,
once the output capacitors are selected and a maximum
allowable ripple voltage, V P-P(MAX) , is determined from an
analysis of the available output voltage budget. Equation 22
can be used to determine a lower limit on the output
inductance.
(EQ. 22)
f S ? V IN ? V P-P ( MAX )
Since the capacitors are supplying a decreasing portion of
the load current while the regulator recovers from the
transient, the capacitor voltage becomes slightly depleted.
The output inductors must be capable of assuming the entire
load current before the output voltage decreases more than
layout and printed circuit design minimizes the voltage
spikes in the converter. Consider, as an example, the turn-off
transition of the upper PWM MOSFET. Prior to turn-off, the
upper MOSFET was carrying channel current. During the
turnoff, current stops flowing in the upper MOSFET and is
picked up by the lower MOSFET. Any inductance in the
switched current path generates a large voltage spike during
the switching interval. Careful component selection, tight
layout of the critical components, and short, wide circuit
traces minimize the magnitude of voltage spikes.
There are two sets of critical components in a DC/DC
converter using a ISL8101 controller. The power
components are the most critical because they switch large
amounts of energy. Next are small signal components that
connect to sensitive nodes or supply critical bypassing
current and signal coupling.
Note that as the ISL8101 does not allow external adjustment
of the channel-to-channel current balancing (current
information is multiplexed across a single R ISEN resistor), it
is important to have a symmetrical layout, preferably with the
controller equidistantly located from the two power trains it
controls. Equally important are the gate drive lines (UGATE,
LGATE, PHASE): since they drive the power train MOSFETs
using short, high current pulses, it is important to size them
accordingly and reduce their overall impedance. Equidistant
placement of the controller to the two power trains also helps
keeping these traces equally long (equal impedances,
resulting in similar driving of both sets of MOSFETs).
4 ? C ? V OUT
2
Δ V MAX . This places an upper limit on inductance.
L ≤ -------------------------------- ? ( Δ V MAX – Δ I ? ESR )
( Δ I )
(EQ. 23)
The power components should be placed first. Locate the
input capacitors close to the power switches. Minimize the
length of the connections between the input capacitors, C IN ,
and the power switches. Locate the output inductors and
While Equation 23 addresses the leading edge, Equation 24
gives the upper limit on L for cases where the trailing edge of
the current transient causes a greater output voltage
deviation than the leading edge.
output capacitors between the MOSFETs and the load.
Locate the high-frequency decoupling capacitors (ceramic)
as close as practicable to the decoupling target, making use
of the shortest connection paths to any internal planes, such
L ≤ ----------------- ? ( Δ V MAX – Δ I ? ESR ) ? ( V IN – V O )
( Δ I )
2.5 ? C
2
16
(EQ. 24)
as vias to GND immediately next, or even onto the capacitor
solder pad.
The critical small components include the bypass capacitors
for VCC and PVCC. Locate the bypass capacitors, C BP ,
FN9223.1
July 28, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| EMA28DTAS | CONN EDGECARD 56POS R/A .125 SLD |
| EBM28DWWN | CONN EDGECARD 56POS .156 SQ WW |
| HIP6004BCBZA-T | IC CTRLR PWM VOLTAGE MON 20-SOIC |
| LT3024EDE#PBF | IC REG LDO ADJ .5A/.1A 12-DFN |
| ASM24DRKS | CONN EDGECARD 48POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8101EVAL1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Two-Phase Multiphase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL8101IRZ | 功能描述:电压模式 PWM 控制器 W/ANNEAL P6 TWO PHS W/INT DRVRS GEN PURP RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL8101IRZ-T | 功能描述:电压模式 PWM 控制器 W/ANNEAL P6 TWO PHS W/INT DRVRS GEN PURP RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL8102 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL8102CRZ | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。