参数资料
型号: JN5139/001,531
厂商: NXP Semiconductors
文件页数: 19/82页
文件大小: 0K
描述: MCU 802.15.4 32BIT 2.4G 56-QFN
标准包装: 500
系列: JN5139-001Rx
频率: 2.4GHz
调制或协议: 802.15.4 Zigbee
应用: 通用
功率 - 输出: 3dBm
灵敏度: -96dBm
电源电压: 2.7 V ~ 3.6 V
电流 - 接收: 37mA
电流 - 传输: 37mA
数据接口: PCB,表面贴装
存储容量: 96kB RAM,192kB ROM
天线连接器: PCB,表面贴装
工作温度: -40°C ~ 85°C
封装/外壳: 56-VFQFN
包装: 带卷 (TR)

6 Reset
A system reset initialises the device to a predefined state and forces the CPU to start program execution from the
reset vector. The reset process that the JN5139 goes through is as follows.
When power is applied, the internal 32kHz oscillator starts up and stabilises, which takes approximately 100 μ sec. At
this point, the 16MHz crystal oscillator is enabled and power is applied to the processor and digital logic. The logic
blocks are held in reset until the 16MHz crystal oscillator stabilises, which typically takes 2.75ms.
Once the oscillator is up and running the internal reset is removed from the CPU and peripheral logic and the CPU
starts to run code beginning at the reset vector, consisting of initialisation code and the resident Boot Loader
(described in JN-AN-1003 Boot Loader Operation [2]).
Section 17.3.1 provides detailed electrical data and timing.
The JN5139 has three sources of reset:
?
?
?
Internal Power-on Reset
External Reset
Software Reset
Note : When the device exits a reset condition, device operating
parameters (voltage, frequency, temperature, etc.) must be met to ensure
operation. If these conditions are not met, then the device must be held in
reset until the operating conditions are met. (See section 17.3.1)
When reset is low, the digital logic and RAM are not powered and therefore anything stored in the RAM after reset is
released cannot be guaranteed to still be valid.
6.1 Internal Power-on Reset
For the majority of applications the internal power-on reset is capable of generating the required reset signal. When
power is applied to the device, the power-on reset circuit monitors the rise of the VDD supply. When VDD reaches
the specified threshold, the reset signal is generated and can be observed as a rising edge on the RESETN pin. This
signal is held internally until the power supply and oscillator stabilisation time has elapsed, at which point the internal
reset signal is then removed and the CPU is allowed to run.
VDD
Internal RESET
RESETN Pin
Figure 10: Internal Power-on Reset
The external resistor and capacitor provides a simple reset operation when connected to the RESETN pin, as shown
in Figure 11. This can be used to extend the reset length and help in systems with noisy reset push-buttons.
? NXP Laboratories UK 2010
JN-DS-JN5139 1v9
19
相关PDF资料
PDF描述
JN5139-EK000 KIT EVAL IEEE802.15.4 JN5139
JN5139/Z01,515 IC MCU ZIGBEE 32BIT 2.4G 56QFN
JN5139-Z01-M/02R1V MODULE ZIGBEE SMA CONN HP JN5139
JN5148/001M04T,534 MODULE ZIGBEE PRO HP U.FL CONN
JN5148-UG010 KIT UPGRADE ZIGBEE PRO
相关代理商/技术参数
参数描述
JN5139-001-M/00R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/01R1V 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/02R1V 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/03R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/04R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm